Mole of argon gas is bubbled through a large volume

Assignment Help Mechanical Engineering
Reference no: EM13714157

When one mole of argon gas is bubbled through a large volume of an Fe-Mn melt of xMn = 0.5 at 1863 K evaporation of Mn into the argon causes the mass of the melt to decrease by 1.5 g. The gas leaves the melt at a pressure of 1 atm. Calculate the activity coefficient of Mn in the liquid alloy.

Reference no: EM13714157

Questions Cloud

Calculate how far the tendon stretches : Human feet and legs store elastic energy when walking or running. They are not nearly as efficient at doing so as kangaroo legs, but the effect is significant nonetheless. Calculate how far the tendon stretches
The collective bargaining agreement expired : When the Collective Bargaining Agreement expired on September 22, 1985, representatives of Oxford Woodworking and international Woodworkers of America began negotiations. They agreed to extend the agreement from one meeting to another; however..
Consider a sphere of porous material of radius : Consider a sphere of porous material of radius R surrounded by a gas having mole fraction XA0 (or, if you prefer, CA0) the bulk of the gas. Derive the differential equation that when solved will give the mole fraction of gas A (XA) [or the concentrat..
Find what is the current in the light bulb : A light bulb has a resistance of 170 ohm when operating with a potential difference of 170 V across it. What is the current in the light bulb
Mole of argon gas is bubbled through a large volume : When one mole of argon gas is bubbled through a large volume of an Fe-Mn melt of xMn = 0.5 at 1863 K evaporation of Mn into the argon causes the mass of the melt to decrease by 1.5 g. The gas leaves the melt at a pressure of 1 atm. Calculate the acti..
Assumptions about drop size and unit cost of energy : A US Department of Energy article states that a leak of one drip of hot water per second can cost $1.00 per month. Making reasonable assumptions about drop size and unit cost of energy, determine if this claim is reasonable.
Single-row deep groove ball bearing is to withstand : A single-row deep groove ball bearing is to withstand a 400 lb. radial load at 100 rpm. It is desired that the bearing has a life of 5000 hrs. And a failure probability of 6 % Determine the Basic Load Rating of this bearing if the inner ring is rotat..
Calculate what minimum speed must the cylinder have : In a rotor ride, which is a large hollow cylinder that is rotated rapidly around its central axis, people are rotated at a high speed. What minimum speed must the cylinder have
Evaluate what is the coefficient of static friction : A racecar travels at 14 m/s and turns in a circle on a flat track with a radius of 10 m. What is the coefficient of static friction between the car's tires and the track

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Use only two iterations and take t 2 and t 35 seconds as

the velocity of a body is given by vt 5e-t 6 where v is in ms and t is in seconds. use the secant method to find when

  Based on inernal energy considerations what dislocation

based on inernal energy considerations what dislocation density in cu is needed to make the crystalline form of cu

  Compared to cross-linked polymers-linear polymer chains

Compared to cross-linked polymers, linear polymer chains:

  Two kg of saturated liquid water at 1 bar is compressed to

two kg of saturated liquid water at 1 bar is compressed to 25 bar and 100degc in a water pump. determine the change in

  How accurate is the ideal gas model for predicting the mass

1. an employee at general electric must order bottles of compressed methane to run her gas oven test facility. the

  Natural gas having a molar analysis

Natural gas having a molar analysis of 60% methane (CH4) and 40% ethane (C2H6) enters a compressor at 340K, 6 bar and is compressed isothermally without internal irreversibilities to 20 bar. The compressor operates at steady state, the kinetic and po..

  Find the axial pressure of the unit normal pressure

A multiple disc clutch employs 3 steel and 2 bronze discs having outer diameter 300 mm and inner diameter 200 mm. For a coefficient of friction of 0.22 find the axial pressure and the power transmitted at 750 r.pm if the normal until pressure is 0.13..

  A male reactor operator receives a whole body dose

a male reactor operator receives a whole body dose equivalent of 0.96 rem over a period of one week while working with

  Estimate the moisture picked up by 1 kg of dry air and the

a grain dryer consists of a vertical cylindrical hopper through which hot air is blown. the air enters the base at 1.38

  90 fpm for 30 min 80 fpm for 90 min 75 fpm for 150 min a

if a bar of sae 1040 is to be turned with a high speed steel tool with a feed of 0.015 per revolution and a depth of

  What is the air temperature at the stagnation point

A high performance F-16 fighter is flying at Mach 0.96 at sea level. What is the air temperature at the stagnation point at the leading edge of the wing?

  Dimensions of the heat exchanger with a pressure drop

A balanced-cross-flow compact heat exchanger is required for an air heating system that processes 0.5 kg/s air. The inlet temperature for the hot water is 295 K, and the cold air enters at 270 K to be heated to 287 K. The inlet pressure for the hot w..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd