Maximum amount of work the engine

Assignment Help Mechanical Engineering
Reference no: EM13872985

A car engine burns 5 kg fuel (equivalent to addition of QH) at 1500 K and rejects energy to the radiator and the exhaust at an average temperature of 750 K. If the fuel provides 40 000 kJ/kg what is the maximum amount of work the engine can provide?

Reference no: EM13872985

Questions Cloud

Traction force between the tires and the road : A car uses 25 hp to drive at a horizontal level at constant 100 km/h. What is the traction force between the tires and the road?
Comparison-contrast essay : Comparison-Contrast Essay
Ifrs differ from u.s. gaap : With regard to write downs of inventory under the lower of cost or market method, how do IFRS differ from U.S. GAAP?
What advantages do you see to the bundle theory : What is it that makes you the 'I' that you are? What advantages do you see to the "Bundle Theory" as opposed to the "Soul Theory," and what would giving up the "Soul Theory" mean?
Maximum amount of work the engine : A car engine burns 5 kg fuel (equivalent to addition of QH) at 1500 K and rejects energy to the radiator and the exhaust at an average temperature of 750 K. If the fuel provides 40 000 kJ/kg what is the maximum amount of work the engine can provid..
Write an essay on -anger : A definition essay asks the writer to concentrate on the clarification of the meaning of the concept or word. This does not mean the writer should provide a dictionary definition.
What kind of strategy do you have regarding fuel : Have you found that you're able to influence areas that previously would have been out of reach for procurement? What kind of strategy do you have regarding fuel? Aside from fuel, what are the other core categories for you
Find the required force : A bucket of concrete of total mass 200 kg is raised by a crane with an acceleration of 2 m/s2 relative to the ground at a location where the local gravitational acceleration is 9.5 m/s2. Find the required force.
How is population health best to be advanced : Choose one between these two: This assignment will be sent through 'safe assign' so no plagiarism please. Present both sides on "abortion vs. the right to life," and b) take a stand on the issue. What are the determinants of population health, and b)..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Force on piston is proportional to cylinder volume squared

A cylinder fitted with a piston containing 1kg of Refrigerant 134a at 20C and 90% vapor quality is attached to a line flowing Refrigerant 134a. The total force on the piston is proportional to the cylinder volume squared.

  Estimate the net amount of work done by the mass on the

5 mol of an ideal gas are stored in a piston and cylinder arrangement. the cross-sectional area of the cylinder is 0.1

  Temperature of the steam entering the turbine

Steam is produced at 70 bar and some unknown temperature. A small amount of steam is bled off just before entering a turbine and goes through an adiabatic throttling valve to atmospheric pressure. The temperature of the steam exiting the throttling v..

  The average speed in the discharge pipe is 3 ms if the pump

a pump draws water from a reservoir through a 150 mm diameter suction pipe and delivers it to a 75 mm diameter

  In the refrigeration cycle the evaporator operates at 10oc

a rankine cycle is used to generate electricity with a total plant capacity of 65 mw. heat from the condenser is

  External effects other then gravitational force cont

How can we rotate a disc hanged with weights freely without external effects other then gravitational force cont?

  A manometer on the discharge pipe of a pump handling

A manometer on the discharge pipe of a pump handling 8.4m^3/min of water shows a pressure of 3.7*10^5 Pa. The vacuum gage on the suction pipe shows a vacuum of 21 cm Hg. The vertical distance between the places of connection of the manometer and the ..

  Knowing that the tank contains compressed air under a

the tank shown has a 180 mm inside diameter and a 12 mm wall thickness. knowing that the tank contains compressed air

  Determine the stress in ab and bc as well as the

the gap at c is initially 0.15mm before load p is applied. for p200kn the gap will close. determine the stress in ab

  What is the specific volume of water at 50 mpa and 80

what is the specific volume of water at 50 mpa and 80 degrees celcius. what would it be if the incompressible liquid

  Find a cutting speed for minimum tool wear b machining time

a work piece 400 mm x 70 mm in diameter is to be machined. the material has constants n0.23and c250 mmin. disposable

  If at this instant the center of the wheel c has a

a 600 mm diameter wheel rolls without slipping on a horizontal surface as shown. rod ab is attached to the wheel at a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd