Magnitudes of their velocities

Assignment Help Mechanical Engineering
Reference no: EM13701623

Two planes A and B are flying at the same altitude. if the magnitudes of their velocities are va = 500 km/h and vb=450km/h such that the angle between their straight line courses is theta=75 degrees , determine the magnitude in km/h of the velocity of plane B relative to plane A.

Reference no: EM13701623

Questions Cloud

Fluid is moving between two plates the top plate : Fluid is moving between two plates the top plate is moving with a velocity V, the distance between the plates is h, and the flow is completely horizontal; select the appropriate boundary condition of the viscous flow.
Determine the magnitude of the acceleration of the van : The engine of the van produces a constant driving traction force F at the wheels as it ascends the slope at a constant velocity v, determine the magnitude of the acceleration of the van,in m/s^2 .when it passes point A and begins to travel on a level..
Find the amount of return air and outdoor air in cfm : A building has a calculated cooling load of 24 tons, of which 6 tons is latent load. The space is to be maintained at 72 F db and 50% relative humidity. 15% by volume of the air supplied to the space is outdoor air at 95 F db and 65% relative humidit..
The x-component of the velocity of plane : The velocity of plane B relative to plane A can be expressed in the following form vb/a = Mi+Nj M i is the x-component of the velocity of plane B relative to plane A. what is the value of M, in km/h ?
Magnitudes of their velocities : Two planes A and B are flying at the same altitude. if the magnitudes of their velocities are va = 500 km/h and vb=450km/h such that the angle between their straight line courses is theta=75 degrees , determine the magnitude in km/h of the velocity o..
Calculate the heat transfer rate for the intercoole : In a cold air-standard Brayton cycle, air enters a compressor operating at steady state at 15 lb/in2, 80 degress F, with a volumetric flow rate of 6000 ft3/min. The compression occurs in two stages and the pressure ratio across each stage is the same..
Case study : What do you think? Does this case present an ethical issue? If so, to which party (or parties)? If you could act as the ultimate authority on this situation, what would you do?
Design a class box that defines a box on a floor : You will Design a class box that defines a box on a floor. A box has a number and an (a,b) location where a and b are numbers between -5, and 5. The key member function is plot, which plots the box.
Prove that the languages are not regular : Prove that the subsequent languages are not regular using the pumping lemma. Use 'N' as the pumping lemma constant, to differentiate from the lowercase n used in parts a and b.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the pressure in lbfin2 at the bottom of the tank

the pressure from water mains located at street level may be insufficient for delivering water to the upper floors of

  Determine the acceleration of the cabinet

Determine the acceleration of the cabinet when sA = 40 ft. Note that when sB = 0, sA = 0 (points A and B are coincident).

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  When a potential difference of 144 v is applied to the

when a potential difference of 144 v is applied to the plates of an air-filled parallel-plate capacitor the plates

  Hydrogen at 25 bar 450degc enters an adiabatic turbine and

hydrogen at 25 bar 450degc enters an adiabatic turbine and expands to 2 bar 160degc with a mass flow rate of 0.2 kgs.

  A variable force and appropriate energy transfers are

ten kilograms of water initially at 3000 kpa 200degc are contained in a piston-cylindernbspdevice shown below. a

  A rigid tank contains an ideal gas at 1227 c and 200 k pa

a rigid tank contains an ideal gas at 1227 c and 200 k pa. the gas is cooled until the gauge reads 50 k pa. if the

  Velocity profile from the navier-stocks equations

I need to be able to derive the velocity profile from the navier-stocks equations. Basically from scratch. Problem 4.36 in the fluid mechanics seventh edition Frank M. White In need to get derived down to the Differential form and find the constant o..

  Wat is the time expression for the motor response if the

the 500 lbf motor is supported on springs with a total stiffness of 5000 lbfin. the springs have a damping ratio of

  A nozzle is attached to a vertical pipe and discharges

a nozzle is attached to a vertical pipe and discharges water into the atmosphere as shown in the figure. when the

  Calculate the force required in direct extrusion

Calculate the force required in direct extrusion of 1100-O aluminum from a diameter of 6 in. to 2 in. Assume that the redundant work is 30% of the ideal work of deformation, and the friction work is 25% of the total work of deformation.

  What should the diameter of the nozzle outlet be

What should the diameter of the nozzle outlet be in inches and what is the mass flow rate of steam through the nozzle in lbm/min?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd