Lighting system along with electrical power distribution

Assignment Help Electrical Engineering
Reference no: EM131037988

Introduction to Building Services and Design

Task:

Using CIBSE guides and Building Regulations Approved Documents as references, design a lighting system along with electrical power distribution.

You are provided with the site plan to help you in preparing your report, which should include the following:

- fully referenced schematic diagrams of the proposed system,
- location of Luminaires and switches, giving reasons for location.

You should comment on the luminaire chosen taken into consideration the following:
- suitability
- first cost
- running costs
- maintenance and life expectancy.

Comment on the affective use of natural daylight.

Show fully referenced schematic diagrams of your proposed electrical power distribution on the site plan, including location of consumer unit and power outlet, giving reasons for location. Make sure you have left the system adaptable for additional developments.

The report must include full referencing and where possible manufacture's data to support your design.

1595_Portfolio.jpg

Verified Expert

Reference no: EM131037988

Questions Cloud

Describe the attitude-toward-the-ad model : Describe the attitude-toward-the-ad model. State a minimum of three facts about the model. Describe how a person’s attitude toward a brand of your team’s choice (name the brand) was formed, based on what this model says about attitude formation.
Find the range of speed of the gonernor : In addition, there is an equivalent constant inward radial force of 80N acting on each revolving mass in order to allow for the dead weight of mechanism - find the range of speed of the gonernor.
Prevent the revolution and the fall of the monarchy : Given their fundamental differences, why did communism and fascism have such similar outcomes in the middle third of the twentieth century? What forces at work in Western civilization caused their high ideals to produce such nightmarish results
Preventing or mitigating dos or distributed dos : The course module #4 covers very important concepts of how Denial of Service (DoS) attacks work. However, the module does not discuss detection, prevention, or mitigation of DoS attacks (or Distributed DoS). The task of this individual assignment ..
Lighting system along with electrical power distribution : Design a lighting system along with electrical power distribution - Using CIBSE guides and Building Regulations Approved Documents as references, design a lighting system along with electrical power distribution.
Pizza employs sigfried as a delivery driver : Rush’s Pasta & Pizza employs Sigfried as a delivery driver. Rush’s guarantees that an order will be delivered within thirty minutes or there is no charge, and insists that its drivers meet the limit. One night, while making a delivery, Sigfried is ca..
Question regarding the communication plan : The experts explain that a communication plan should describe needs and expectations. It should also be specific to need to know parties, as well as being consistent and timely.
Buffered versus unbuffered queries : Q1 Write the difference between Buffered Versus Unbuffered Queries. Q2 Define Cookies and give an example as a coding (servlet) for a cookies?
Research primary and secondary sources : a short summary of how you intend to research primary and secondary sources (with at least some indication of what sources you will use and what they will provide)

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the values of l and c and the cutoff frequencies

Design a series resonant circuit to have a bandwidth of 400 Hz using a coil with a Ql of 20 and a resistance of 2-ohm. Find the values of L and C and the cutoff frequencies

  Calculate the potential difference vab between two shells

Calculate the potential difference Vab between two concentric spherical shells of charge. Assume that the inner shell has a radius a and chargeQ, and the outer shell has a radius b and charge-Q.

  Expression for evaluating the measurement error

Derive an expression for evaluating the measurement error, ?Terr = Ttip - T8,i, which is the difference between the tip temperature, T lip , and the water temperature, T8.i'

  List the state table for the sequential circuit

A sequential circuit with two D flip flops, two inputs x and y, and one output z is specified by the following next state and output equations: A(t + 1) = xy + x'B B(t + 1) = y'A' + yB

  At which zero power is being delivered to the resistor

A sinusoidal voltage source vs = 100cos 105t V, a 500Ω resistor, and an 8 mH inductor are in series. Determine those instants of time, 0≤t

  How many charges need to move across the membrane

During an AP, the membrane potential typically moves from -70mV to +20mV and back again. In a cell with 10um radius and 1uF/cm^2, how many charges need to move across the membrane (and back again) to get this 90 mV voltage fluctuation?

  How much current flows through the light bulb

Using the symbols we've learned in class (standard symbols used universally), draw a schematic showing the circuit of a 12-V car battery (represented as a voltage source connected to a light bulb (represented as a resistor).

  Calculate the dc voltage that would be measured across r2

Calculate the dc voltage that should exist across R2 without the Voltmeter present. Calculate the dc voltage that would be measured across R2 using a 10 kΩ/V analog voltmeter set to the 10-V range.

  Ask-fsk waveform generation

Describe your design process, how you made decisions, trouble you had, changes you made to the design to make it work, how you figured out significant values (frequencies,etc).

  Find frequency that will cause inductor to have impedance

1. Determine the capacitance for a capacitorif its impedance is 5000 ohms at 400 radians/second. 2.Calculate the frequency that will cause a100mH inductor to have an impedance of 15,708 ohms.

  What would be the percentage change in field intensity

If the power of a 500-kHz transmitter is increased from 150 W to 300 W, what would be the percentage change in field intensity at a given distance from the transmitter. What would be the decibel change in field intensity.

  What is difference between the atoms of conductive substance

Early scientific researchers hypothesized that electricity was an invisible fluid that could move through certain substances. Those substances "porous" to this "fluid" were called conductors, while substances impervious to this "fluid" were called..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd