Lf the 50-kg crate starts from rest and achieves a velocity

Assignment Help Mechanical Engineering
Reference no: EM13609828

lf the 50-kg crate starts from rest and achieves a velocity of v = 4 m/s when it travels a distance of 5 m to the right, determine the magnitude of force P acting on lhe crate. The coeificient of kinetic friction between the crate and the ground is uk = 0.3. P is pulling at a 30 degree angle up from center.

Reference no: EM13609828

Questions Cloud

What is the correct journal entry to record direct labor : what is the correct journal entry to record direct labor when the actual labor mix is favorable and the total standard
Crates a and b weigh 100 lb and 50 lb respectively if they : crates a and b weigh 100 lb and 50 lb respectively. if they start from rest determine the their speed when t 5s. also
There are several reasons why actual results differ from : there are several reasons why actual results differ from standards. which of the following does not represent a reason
A company issues 1 million of new stock and pays 200000 in : a company issues 1 million of new stock and pays 200000 in cash dividends during the year. in addition the company took
Lf the 50-kg crate starts from rest and achieves a velocity : lf the 50-kg crate starts from rest and achieves a velocity of v 4 ms when it travels a distance of 5 m to the right
The traditional view about the normal curve in psychology : the traditional view about the normal curve in psychology is that normal curves are 6a rare in nature but often occur
A company established a direct material standard of 2 : a company established a direct material standard of 2 pounds of material at a cost of 6 per pound for unit produced.
If two service departments service the same number of : if two service departments service the same number of departments which service departments costs should be allocated
Martha and jones have capital balances on january 1 of : martha and jones have capital balances on january 1 of 50000 and 40000 respectively. the partnership income-sharing

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  For the same electrical output what is the percent

a fossil-fuel steam power plant operates at about 50 of carnot thermal efficiency. it has been suggested that the air

  Define- hydraulic mean radius

Define- hydraulic mean radius, hydraulic dept, section factor and most efficient dhannel cross section.

  Te point starts moving at t0 find the total distance

the position of a point p on a line is given by the equation x t sinpi t2. the point starts moving at t0. find the

  How to create a directory called class

make a text file that contains what is your absolute path, and call it paths.txt

  The steam is compressed at constant pressure until its

a cylinder contains 2 kg of steam at 200 kpa and 200 c. the steam is compressed at constant pressure until its

  Determine the moment of the force

A 90-N force is applied to the control rod AB as shown. Knowing that the length of the rod is 225 mm, determine the moment of the force about point B by resolving the force into horizontal and vertical components.

  Determine the pressure and the internal energy

refrigerant -134a at 800kPa and 25 C is throttled to a temperature of -20C. determine the pressure and the internal energy of the refrigerant at the final state.

  Etermine the principal stresses and maximum shearing stress

four forces are applied to a W200x35.9 rolled beam as shown. determine the principal stresses and maximum shearing stress at point a.

  Determine the following a pressure psi at each state b mass

a closed rigid tank contains 5 lbm of a two phase mixture of water initially at 260degf with a quality of 0.6. heat

  Calculate the battery failure probability under normal

a particulate monitor has a power supply consisting of two batteries in parallel. either battery is adequate to

  An airplane wing modeled as a spring-mass system with

an airplane wing modeled as a spring-mass system with natural frequency 40 hz is driven harmonically by the rotation of

  Part-1link parametersbull a draw a cad model of an rr link

part-1link parametersbull a draw a cad model of an rr link shown in fig.you may represent an r joint as in fig or using

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd