Knowing that the coefficient of restitution between the

Assignment Help Civil Engineering
Reference no: EM13531122

A 2-lb sphere A is moving to the left with a velocity of 40 ft/swhen it strikes the inclined surface of a 5-lb block B which is atrest. The block is supported by rollers and is attached to a springof constant k=12 lb/in. Knowing that the coefficient of restitution between the sphere and the block is e=.7, and neglecting friction,determine the maximum deflection of the spring.

Reference no: EM13531122

Questions Cloud

Determine the approximate drag coefficient for the parachute : A 5-m-diameter parachute of a new design is to be used to transporta load from flight altitude to the ground with an average verticalspeed of 3 m/s. The total weight of the load and theparachute is 200 N. Determine the approximate dragcoefficient for..
Do the same for saturated vapor steam in an adiabatic : Saturated liquid water is in an adiabatic compressor with inlet and outlet pressures of 100 kPa and 1 Mpa. The isentropic efficiency is 85%. Find the work input (kj/kg) and entropy generation (kj/ kg K).Do the same for saturated vapor steam in an adi..
What is the density of the rock before it blasted : You are given the following information about a dry-batchpaving operation. You are going to use one mixer that has a servicerate of 30 serives/hr. The dry-batch trucks you use forbringing concrete to the paver have an arrival rate of 7.5 arrivals/hr...
A street car line on the center of an 80 ft street makes : A street car line on the center of an 80 ft street makes a 75degrees 24' turn into another street of equal width. Thecorner curb line has R=12 ft. What's the largest R that canbe given a circular curve for the tract center line if the law requires it..
Knowing that the coefficient of restitution between the : A 2-lb sphere A is moving to the left with a velocity of 40 ft/swhen it strikes the inclined surface of a 5-lb block B which is atrest. The block is supported by rollers and is attached to a springof constant k=12 lb/in.
Determine the required capacity of the motor of the : A step-type escalator as shown is designed to transport 120 persons per minute at a constant speed v=1.5 ft/s. The overall efficiency of the escalator is estimated to be 70%, and a 200% overload is to be allowed. Assuming that the average weight per ..
What is the underflow flow rate : A settling tank in a water treatment plant has an inflow of 2m3/min and a solids concentration of 2100 mg/L. The effluentfrom this settling tank goes to sand filters. Theconcentration of sludge coming out of the bottom (the underflow) is18,000 mg/L, ..
The mass flow rate of the refrigerant and : Refrigerant R-134a enters the evaporator coils placed at the back of the freezer section of a household refrigerator at 120 kPa with a quality of 20 % and leaves at 120 kPa and -20°C. If the compressor consumes 450 W of power and the COP is 1.2
Determine how much money the home owner would have saved : A house that was heated by electric resistance heaters consumed 1200 kWh of electric energy in a winter month. If this house were heated by a heat pump that has an average COP of 2.4, determine how much money the home owner would have saved that mont..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the net force acting on the body

Starting from rest, a 4.0-kg body reaches a speed of 8.0 m/s in 2.0 s. What is the net force acting on the body?

  Determine what will be the percent conversion

A plug-flow reactor has a conversion of A of 90%, and the reaction is first order. If a dispersed plug-flow reactor has the same volume and has a dispersion number, D/vL of 1.0

  Determine average rate of rainfall incubic feet per second

Rain falls at an average intensity of 0.4 in/h over a 600-acre areafor 3 days. a) Determine the 3-days volume of rainfall in acre-ftand ft3,b) determine the average rate of rainfall incubic feet per second

  How do you find the maximum axial load using asd

An 8x12 column of No. 1 Spruce-Pine-Fir(South) has an unbraced length for buckling about the strong x axis of 16 feet and an unbraced length for buckling about the weak y axis of 8 ft. Cm = 1.0 and Ct = 1.0

  What is velocity of blocks 5 after blocks started moving

What is the velocity of the blocks 5.00 after the blocks have started moving. Assume that the rope joining the two blocks in long enough so that, at this time, block A is on the frictionless surface while block B is still on the rough surface.

  Calculate moment of inertia of the hollow rectangular steel

A hollow rectangular steel beam is 18 cm deep by 10 cm wide, outside dimensions. The walls are 2 cm in thickness. From the shear and moment diagram, the maximum vertical shear on the section is 180 kN.

  Determine the net power delivered to the generator

Air enters the compressor at 98 kPa and 295 K at a rate of 10 kg/s and exits at 1 MPa and 620 K. Determine the net power delivered to the generator by the turbine.

  Determine the external wind pressure acting on the windward

A closed storage building is located on open flat terrain in central ohio. If the side wall of the building is 20ft high, determine the external wind pressure acting on the windward and leeward walls. Each wall is 60ft long.

  Find probability that the percent absorbed is more than 10

When a pesticide comes into contact with skin, a certain percentage of it is absorbed. The percentage of the pesticide that will be absorbed during a given tie period can be modeled with a lognormal distribution.

  Calculating largest tolerable internal crack length

Calculate the largest tolerable internal crack length for a 7075-T651 aluminum alloy component that is loaded to a stress one-half of its yield strength without catastrophic fracture.

  Determine what is the shortest height tank should be

An engineering student has been given the assignment of designing a hydraulic holding system for a hay baling system. The system has four cylinders with 120 mm diameter pistons with a stroke of 0.320 m.

  Estimate the energy required to raise the temperature

Estimate the energy required to raise the temperature of 2 kg (4.42 lbm) of the following materials from 20°C to 100°C (68°F to 212°F): aluminum, steel, soda-lime glass, and high-density polyethylene.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd