Is there any appreciable advantage to placing the drains

Assignment Help Civil Engineering
Reference no: EM13543399

Within a field that is used for agricultural production, a clay unit is found at a depth 8ft below the land surface. the surface soil has a hydraulic conductivity of .6 ft/d. if parallel drains are placed 2 in per day. and if water level is to be maintained below 18 in from the ground surface, what is the maximum allowable lateral drain spacing?

Is there any appreciable advantage to placing the drains 1 ft above the clay pan?

Reference no: EM13543399

Questions Cloud

Determine the adjusted asd values associated with the : A 24F-V4 Douglas Fir-Larch glulam is used to span 32 ft, carrying an ASD load combination (D + S). The load is uniform over a simple span, and the beam is laterally supported so that lateral torsional buckling is prevented.
What would be the values of density and water content if the : A soil has a bulk density of 1.91 Mg/m^3 and a water content of 9.5%. The value of Gs is 2.70. Calculate the void ratio and degree of saturation of the soil. What would be the values of density and water content if the soil were fully saturated at th..
Calculate also the unit weight and water content at a degree : Calculate the dry unit weight, the saturated unit weight and the buoyant unit weight of a soil having a void ratio of 0.70 and a value of Gs of 2.72. Calculate also the unit weight and water content at a degree of saturation of 75%.
Determine the density index of the sand : The in-situ dry density of a sand is 1.72 Mg/m^3 . The maximum and minimum dry densities, determined by standard laboratory tests, are 1.81 and 1.54 Mg/m^3, respectively. Determine the density index of the sand.
Is there any appreciable advantage to placing the drains : Within a field that is used for agricultural production, a clay unit is found at a depth 8ft below the land surface. the surface soil has a hydraulic conductivity of .6 ft/d. if parallel drains are placed 2 in per day
Show periodic inventory system : Complete the worksheet by extending amounts reported in the adjustment trial balance to the appropriate columns in the worksheet. The company uses the periodic inventory system.
Draw the flow net and determine the quantity of seepage : For a ternary system, three components are present; temperature is also a variable. What is the maximum number of phases that may be present for a ternary system, assuming that pressure is held constant?
Calculate equivalent units of transferred-in costs : Calculate equivalent units of transferred-in costs, direct materials, and conversion costs - summarize total costs to account for, and calculate the cost per equivalent unit for transferred-in costs, direct materials, and conversion costs.
What was the investors actual real after tax rate of return : What was the investors actual real after tax rate of return and the firm may ask a bank for which of the following to allow it to obtain the permits?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Vehicle delay due to queuing

Vehicles begin to arrive at a toll booth at 850 am with an arrival rate of x(t) = 4.1 + .01t (with t in min and x(t) in veh /min.) The toll booth opens at 9am and processes vehicles at a rate of 12 per minute throughout the day. Assuming D/D/1 que..

  Determine value and location from point d of max moment

Determine the value and location from point D of the maximum internal bending moment and shear force for the member. Take x = 2 ft. Be sure to draw complete free body diagram(s) for full credit.

  Determine max value of dz if the flow is to remain laminar

The slope of the hill is such that for each 1.5 km of horizontal distance, the change in elevation is dz meter. Determine the maximum value of dz if the flow is to remain laminar, with a temperature of T=20°C and pressure all along the pipe is con..

  What total allowable bod kg per day could be discharged

A 5000 m3/day wastewater treatment plant discharges to a river with a minimum drought flow of 140 m3/min (upstream of outfall) a)What total allowable BOD (kg/day) could be discharged by the plant if the BOD in the river after initial dilution must ..

  Determine dead load in pounds per linear foot from concrete

A three span continuous beam has spans of 27, 30, and 27 feet. The beams support one-way slabs, 6 inches thick that span 20 feet center to center. Assume that the beams are 16 inches wide and 24 inches deep.

  What is the so2 concentration at a sampling point located

If the effective stack height of the plant is 100 m, and the ground reflects the SO2 emission perfectly what is the SO2 concentration at a sampling point located 2 m above the ground in the town.

  Determine the speed of each car just after the collision

The 15-Mg tank car A and 25-Mg freight car B travel towards each other with the velocities. If the coefficient of restitution between the bumpers is e=0.6, determine the speed of each car just after the collision.

  What is bod5 using a mix consisting of four parts

A standard five-day BOD test is run using a mix consisting of four parts distilled water and one part wastewater (no seed) the initial DO of the mix is 9.0 mg/l , and the do after Five days, determined to be 1.0mg/l. what is BOD5

  Explain lift charts in direct marketing

Lift Charts in direct marketing, The mass-mailing business is often used to illustrate the use of lift charts. Another real world application where the lift charts can be used

  Determine the required mass of block a from rest

Determine the required mass of block A so that when it is released from rest it moves the 5-kg block B a distance of .75m up along the smooth inclined plane in t=2s. Neglect the mass of the pulleys and cords.

  What is the maximum grade the vehicle could ascend

the engine develops a maximum torque of 210ft-lb at 3600 rev/min. what is the maximum grade this vehicle could ascend, on a paved surface, while the engine is developing maximum torque (assume that the available tractive effort is the engine-gener..

  Calculate stress along edge c-d caused by applied force

A horizontal prestressing force of 500kN is applied to a rectangular beam. The beam has a depth of 450mm and a width of 250mm. The force is applied at a distance of 60mm below the sections x-x axis.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd