Investigate and analyse client and user requirements

Assignment Help Other Engineering
Reference no: EM131189487

Learning outcomes

This assessment will test your ability to meet the learning outcomes as described in your module booklet, specifically:

1. Critically think and solve engineering design problems

2. Investigate and analyse client and user requirements, technical briefs and apply ?significant knowledge to design scenarios

3. Analyse, synthesise and evaluate relevant technological, engineering, legal, health &? safety and development factors in order to produce novel design solutions which will ?satisfy aesthetic, environmental, production and performance criteria

4. Evaluate design team provision and develop appropriate working methods

Assignment Details

A company is at the start of the process of designing a new 7 storey office block to be located in Preston (England) with a single stair.
The floor to floor height is to be 3.4m with the top storey of the building at 23.8m above ground. There will be approximately 360m2 of office accommodation at each level.

The design is an initial concept and there are currently no plans available.

Your task is to review the basic concept against the recommendations of Volume 2 of Approved Document B (2013) on how to meet the functional requirements of the Building Regulations and create an A1 poster presentation highlighting the key recommendations of the guidance that apply and any obvious non-compliances. Where there are non- compliances you should discuss these and try to offer potential solutions/justification.

The poster should cover key aspects of the design and guidance including:

 B1:

- Fire alarm and detection
- Estimating occupant numbers,
- Travel distance limitations
- Exit width requirements
- Stair requirements
- Disabled evacuation

 B3:
- Structural fire resistance
- Compartmentation requirements

 B4:?
- External fire spread via surfaces of the building
- External fire spread to neighboring buildings

 B5:?
- Firefighting shaft requirements (e.g.)
- Level of fire resisting protection require.
- Ventilation requirements
- Provision of firefighting lifts
- Provision of risers.?
o Vehicle access requirements

The review should focus on the requirements of Volume 2 of Approved Document B (2013) and documents specified by ADB.

You should prepare your poster using PowerPoint and should submit your assignment electronically only as a PowerPoint file (i.e. no printed version of the poster is required).

Remember:
- You must answer the question set ?
- You must demonstrate that you have met the learning outcomes ?
- As you construct and present your answer, consider the assessment criteria

Reference no: EM131189487

Questions Cloud

Prepare the chief human resources : Summary. The purpose of this section is to prepare the chief human resources officer for entering the arena of this particular negotiation. Be sure to:
What percentage has the index risen : What is its current value? What month is this for? How does its value in this month compare to its value for the same month a year ago? (That is, by what percentage has the index risen? Use the "seasonally adjusted" number.)
How did the double v campaign spark a civil rights movement : How did the Double V campaign spark a civil rights movement? How successful was the Double V campaign? Include geographical, economic, political, and cultural analysis in your answer.
New opportunities also present new challenges : As more businesses establish an online presence and conduct various aspects of their business online, these new opportunities also present new challenges. What best practices would you recommend to establish adequate controls and mitigate potentia..
Investigate and analyse client and user requirements : Critically think and solve engineering design problems and investigate and analyse client and user requirements, technical briefs - Evaluate design team provision and develop appropriate working methods and Investigate and analyse client and user req..
To which factors do you assign the least weight : Briefly summarize the rationale for your weights. Also, which countries rank the highest according to your weighted BLI?
What is disruptive change : What is "disruptive change," and how is this different from "incremental change?" How does disruptive change affect an organization? Provide an example.
Global trade alert website : Go to the Global Trade Alert's Website and read the "About Global Trade Alert" section, located athttp://www.globaltradealert.org/about. On the far left-hand side of the screen, select the following in the drop-down menus:
Calculating the genuine progress indicator : Which factors are not included in GPI, even though they are included in GDP, because they are defensive expenditures or because of differences in accounting methods?

Reviews

Write a Review

Other Engineering Questions & Answers

  Match the signal to the appropriate sketch a thru d above

• Read Chapter 1 in the text Signals and Systems Using MATLAB.?• Work the following homework problems below.

  Design the parement thickness required using gi method

A soil subgrade has following data, Percent lines = 60%, passing through 0.074mm sieve, Liquid limit = 46%, Plastic limit = 21%, Design the parement thickness required using G.I. method.

  Good grammatical form with appropriate business tone

I need to do case 2 from Chapter 7 of Managerial Accounting Jimbalvo 5th edition. I will attached two photos of the case study.

  Find the largest possible positive-going steps at the output

A class AB output stage, resembling that in Fig. 12.11 but utilizing a single supply of +10 V and biased at VI = 6 V, is capacitively coupled to a 100-_ load. For transistors for which / VBE /= 0.7 V at 1 mA and for a bias voltage VBB =1.4 V, what..

  Identifying employment relationship strategic decisions

The difference between 'control' and 'commitment' employment relationships in the workplace. Select the one you support and explain why.

  Temperature end of expansion process

A four-cylinder, four-stroke, 2.2-L gasoline engine operates on the Otto cycle with a compression ratio of 10. The air is at 100 kPa and 60°C at the beginning of the compression process, and the maximum pressure in the cycle is 8 MPa. The compress..

  Determining the overall pressure drop

The parallel galvanized-iron pipe system of Fig delivers water at 20°C with a total flow rate of 0.036 m3/s. If the pump is wide open and not running, with a loss coefficient K = 1.5, determine (a) the flow rate in each pipe and (b) the overall pr..

  The internet for the link to the boston tunnel

Search the internet for the link to the Boston tunnel, "the Big Dig" or the "Channel Tunnel," and London's Millennium Dome. In spite of their poor cost performance, why do you think these projects were supported to their conclusion?

  What is the corresponding depth range in the model

What is the corresponding depth range in the model and determine the required model sediment sizes

  Explore the breadth of the ict field

Explore the breadth of the ICT field, examining your own knowledge, skills, interests and expertise gained from the workplace and/or study in other subjects in the course.

  Circuit design for moisture sensor amplifier

Circuit Design for Moisture Sensor Amplifier

  Find the worst-case values of the noise margins

Assuming that the inverter is in the logic-1 state 50% of the time and in the logic-0 state 50% of the time, find the average power dissipation in a typical circuit. The power supply is 5 V.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd