Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Using Logisim, implement a 3-8 Decoder, both with gate level components and a Decoder component. Use input pins to control the select line inputs, and LEDs for the output display.(Note that the Decoder takes a 3 bit input signal, which can be made by changing the parameters for an input pin to 3 data bits)
A simple voltmeter with a full-scale reading of 50(V) is required. Use a d'Arsonval movement with a rating of 20(mV) at 1 (mA). Calculate the value of the voltmeter resistor, Rv, required to achieve these design specifications.
Suppose a car of mass m moving on a straight west-east highway at velocity v(t) (positive for motion from west to east) experiences aerodynamic drag force with magnitude v(t) opposing its motion.
1- Draw a circuit whose output goes to + V sat . When the input signal is below -4V. the output should be -V sat, when the input is above - 4V 2- Design a - 90 phase shift circuit at 1590 Hz , Then for your design calculate 0 at 15 Hz, & 15 KHz
A calibrated RTD with ALPHA = 0.0041/°C, R = 306.5 Ohms at 20°C, and PD = 30 mW/°C will be used to measure a critical reaction temperature. Temperature must be measured between 50° and 100°C with a resolution of at least 0.1°C.
You balanced a pump impeller by placing a 5 gram weight at a radius of 100 mm. The original vibration amplitude was 10 mm/s, and after adding the balancing weight, the vibration is 1 mm/s. The speed of the pump is 1500 rpm and the weight of the im..
A copper busbar 10cm wide, 5 mm thick, and 10 m long carries a current of 2kA, Calculate the voltage drop if the temperature of the busbar is 120 degree. What is the power loss per meter
What is the value of beta after the following code executes if the input is 5 int beta; cin >> beta; switch(beta){ case 5: beta += 5; case 1: beta++; case 5: beta += 5; break; case 4: beta += 4; }
Make a user interface (using matlab) for amplitude modulation and demodulation without using the ammod and demmod function. The program should ask the user the 3 types of message signal (Square ,sinc,sinusoidal, triangle, sawtooth)
Evaluating Coding Gain, CNR, and BER of a DSSS-CDMA Transmitter, a. A DSSS-CDMA transmitter sends message signals at a rate of 5.0 kbps using a long chip sequence with a rate of 1 M chips per second. In the receiver, what is the processing gain (a..
A coaxial air line has an inner conductor diameter of 2mm and the inner diameter of the outer conductor is 4.6mm. A voltage of 1 V is applied to the inner conductor. Determine the surface charge densities on the inner conductor
When the piston is at its bottom dead center, the gas is initially at 10 psig, 65°F, and 10.5 in 3 . After compression and when the piston is at top dead center, the gas is 180°F and occupies 1.5 in 3 . What would be the new pressure of the gas in..
The aim of this experiment is to develop a bipolar transistor amplifier with a voltage gain of minus 25. The amplifier must accept input signals from a source impedance of 1 kW and provide an undistorted output amplitude of 5 V when driving a 560..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd