Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Consider a PNP BJT optimum designed for low voltage high current gain.(a) Draw energy band diagram with proper labeling with VCB= -0.7V, VEB= 0.7V. Which mode is the BJT operated in?(b) Plot excess minority charges stored in each region with proper labeling for the BJT biased in (a).(c) If the voltage capability of the BJT needs to be increased, which layer(s) should have a higher doping density and which layer(s) should have a lower doping density? Why?(d). If the BJT is now biased into reverse active mode, draw the energy band diagram and label majority and minority carrier activities in the emitter and collector junction regions.(e). How will the BJT's current gain and breakdown voltage be changed in reverse active mode in comparison to that in normal active mode? Why?
A particular diode was measured to have VD = 0.62 V at ID = 5.895 mA. Determine the following: a) the reverse saturation current IS. b) VD for a forward current of 100 mA. Assume VT = 25 mV.
What is the maximum bandwidth of the low pass filters at the receiving end of the link? What bandwidth would you recommend for the LPFs?
Two homogeneous isotropic dielectrics meet on plane x=0. For x > 0, Er1=6 and for x 0. Find: a) E2 for x
1) Modern technology has produced a small 1.5-volt alkaline battery with a nominal stored energy of 150 joules. For how many days will it power a calulator that draws a 2-mA current 2)The current entering the positive terminal of an element is
A three phase, 25-hp, 440-V, 60-Hz, 1750 rpm, wound-rotor induction motor has the following equivalent circuit parameters: R1=0.20 ohms, X1=1.0 ohms, R2=0.15 ohms, X2=0.8 ohms, Xm=30 ohms. The motor is connected to a three phase, 440-V, 60-Hz supply.
An engineer intends to study an input signal with frequency components of 5, 6, and 10 kHz. It is desired that all other frequencies be filtered out. Design an appropriate filter, using L= 210mH and the MINIMUM bandwidth. Find C and R.
An inventor claims to have perfected an engine that wil produce power from energy transferred as heat from a 1000K flame. Energy wil be rejected as heat to the ground at 290 K. A 75 percent energy conversion efficiency is claimed.
The laminated silicon steel core of a transformer has a mean length of 0.06 m and a cross section of 0.005 meter square. there are 150 turns on primary winding and 450 turns on the secondary. the input is 200 V rms at 50 Hz.
Design a square wave oscillator using an (ideal) operational amplifier. Verify your design with Spice-like software waveform. Specifications: peak value: ±5 V, frequency: 1000Hz, duty cycle: 50%.
A lossless transmission line with a characteristic impedance of 75 ohms is terminated by a load of 120 ohms. The length of line is 1.25 lamda. If the line is energized by a source of 100 V (rms) with an internal impedance of 50 ohms
A 277/480V three phase wye system has the following load: M1- Induction Motor, 50hp, n=0.91, PF= 0.89 at full load. M2- Induction motor, 25hp, n=0.9, PF= 0.9 at full load. R- Heater Load, PF=1 M- A synchronous motor to drive a second 25hp load.
A rectangular loop of wire containing a high resistance voltmeter has corners initially at (a/2, b/2, 0), (-a/2, b/2, 0), (-a/2, -b/2, 0) and (a/2,-b/2, 0). The loop begins to rotate about the x axis at constant angular velocity w.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd