How much oil is leaking from the fryer if any

Assignment Help Mechanical Engineering
Reference no: EM131377772

Mass Balance:  Homework Problems

Q1) In a snack frying process, potato chips are being produced at a rate of 1000 kg/h. The chips contain 35 % oil. The frying process is using up 375 kg/h of oil. Assume that the level of oil in the fryer in constant. How much oil is leaking from the fryer, if any?

If the potato dough entering the process contains 40 % moisture and the final chips contain 2% moisture, 2% salt and 3% emulsifier, how much water is being boiled off during frying?  If the dough is made from potato flour containing 10 % water, how much flour is being used? How much emulsifier and salt are being used? Assume that salt and emulsifier are added to the dough.

Q2) In the glucose recycle problem solved in class, 

A. Calculate using Excel and plot sizes of purge (P) and recycle (R) streams as a function of fructose yield (F) for 10% impurity in the incoming glucose stream (G).

B. Also, following the procedure that I went over in the class for P=0, show the first three steps of calculations showing how the values of F, I, an R evolve over time, for P=20 kg.

C. Consider a case when P = R (splitter). Calculate and plot the values of P, x, F as a function of impurity I (vary between 1% to 10%).

Problem on Unsteady State Mass Balance

Q3) A large tank of volume 10 m3 contains salt solution. The tank is half full and the concentration of salt in the tank is 500 grams per liter. In order to dilute the concentration of salt, fresh water is introduced in the tank at a rate of 50 liters/min.  How long will it take to achieve the desired final concentration of 50 grams of salt per liter?  Assume 1) the tank is well mixed 2) it is OK if it overflows.

Plot the concentration of salt in the tank and amount of salt in the tank as function of time.

4) In the sugar purification problem involving a centrifuge, that was solved in the class, calculate and plot the purity of sugar coming out of the dryer as a function of centrifuge efficiency. In the problem that was solved in class, the centrifuge efficiency was 80%. Take several values for the efficiency.

Attachment:- Assignment.rar

Reference no: EM131377772

Questions Cloud

Explain the major source of foreign exposure : INT 620- Provide a brief historical background on the firm you have selected. Include the nature of its products or services. Explain the major geographical exposure. Explain the major source of foreign exposure.
Find a satisfactory combination of d : Determine a satisfactory combination of D, d, N, and wire material. What is the length of the coiled section when unloaded and when the 135 N force is applied?
How to build an effective business continuity program : Discuss the how Business Continuity Planning (BCP) is different from Disaster Recovery Planning (DRP).Research and find various DRP templates for organizations. Please list a least three examples (e.g. NIST, MIT and others). Also, analyze and ar..
Determine a satisfactory combination of d : Determine a satisfactory combination of D, d, N, wire material, and free length of coiled section.
How much oil is leaking from the fryer if any : In a snack frying process, potato chips are being produced at a rate of 1000 kg/h. The chips contain 35 % oil. The frying process is using up 375 kg/h of oil. Assume that the level of oil in the fryer in constant. How much oil is leaking from the ..
Why the mean would be the best measure of sales performance : Use the mean sales for each salesperson to compare the sales volumes. Explain why the mean would be the best measure of sales performance. Under what circumstances might you choose to use the median or mode?
Explain the different types of feasibility studies : Which project management methodology would you choose to run your software development project?- Explain the different types of feasibility studies a project manager can use to prioritize project importance.
Explains what the policy intends to do and how : Suggest a policy that would help mitigate against attacks similar to this one in the future. Justify your choice in one paragraph.Good policies begin with an overview section that summarizes the policy for senior management. Write a summary paragra..
Which phase in systems development life cycle is important : Which phase in the systems development life cycle is the most important?- If you had to skip a phase during the development of a system, which phase would it be and why?

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  What is your estimate of the fluid viscosity

The tube diameter is 2 mm, and the rate of draining is found to be 1.9 cm3 /s. What is your estimate of the fluid viscosity? Is the tube flow laminar?

  Estimate the critirion frequency of the spring

estimate the factor of safety guarding against fatigue failure using a torsional Gerber fatigue failure critirion with Zimmerli date.

  Calculate the power required to drive a steady-flow

calculate the power required to drive a steady-flow compressor if air flowing at a rate of 1kgs enters at 100kpa

  Calculate the heat flux

Neglecting radiation heat loss, calculate the heat flux qe" that must be supplied by the electrical tape to ensure a uniform fluid temperature.

  Determine the temperatures of surface 1 through 4 of the

determine the temperatures of surface 1 through 4 of the furnace cavity of example 13.3 if the entire furnace

  Write a paper over real estate property management

Write a paper over real estate property management and LEED certification.

  Estimate the entropy production rate of the valve

Carry out the preliminary thermodynamic design of a fuel mixing valve for a furnace that efficiently mixes inlet flow streams of air.- Provide a dimensioned engineering sketch and estimate the entropy production rate of your valve.

  Assuming that the bypassed air produces no thrust and

a jet engine is a serial combination of a compressor an adiabatic constant pressure combustor and a turbine in that

  Motor is used to raise

A 100-watt motor (60% efficient) is used to raise a 100-kilogram load 5 meters into the air. How long, in units of seconds, will it take the motor to accomplish this task?

  What are the velocity thermal and concentration boundary

what are the velocity thermal and concentration boundary layers? under what conditions do they all have the same

  Determine the power delivered to the propeller

The compressor pressure ratio is 10 and the compressor has an isentropic efficiency of 85%. The turbine inlet temperature is 1140 K, and its isentropic efficiency is 85%. The turbine exit pressure is 50 kPa. Flow through the diffuser and nozzle is..

  Calculate the velocity of flow

A pitot-static tube is inserted in a pipe carrying water at 10°C. A differential manometer using mercury as the gage fluid shows a deflection of 106 mm. Calculate the velocity of flow.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd