How long will it take the water in the aquifer to travel

Assignment Help Civil Engineering
Reference no: EM13557082

A truck spils 1 gallon of benzene into an aquifer with an area= 50ft^2 Benzene has a solubility of 1750 ppm, and a specific gravity of 0.873. The aquifer ahs a porosity of 0.25, a hydraulic gradient of 0.004 and a hydraulic conductivity of 1000 gpd/ft2.

a. what is the discharge through the aquifer in gpd?

b. How long will it take the water in the aquifer to travel 100 ft?

c. How long will it take to remove 99% of the benzene from the aquifer? Assume that the volume of aquifer affected is 500 ft^2

Reference no: EM13557082

Questions Cloud

Constuct a choice table for interest rate from 0% to 100% : The owner of a downtown parking lot has employed a civil engineering consulting frim to advise him on the economic feasibility of constructing an office building on the site. bill samuels, a newly hired civil engineer, has been assigned to make the a..
What maximum force can this person apply with this jack : A container of petrol on a set of scales is used to measure the rate at which fuel is used by an engine under test. In one test the weight measured by the scales decreases by 25.0 N in 1 hour. (Assume the specific gravity of petrol is 0.720 and g is ..
What is its speed at the point that the force resisting : This problem models an insertion process. Block A (mA = 2kg) is acted on by a horizontal force F (F = 12 N). As A moves to the right, it gets pressed more and more tightly in the channel.
How long will it take for the pce to reach the well : The water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE (ans. 54 days)
How long will it take the water in the aquifer to travel : A truck spils 1 gallon of benzene into an aquifer with an area= 50ft^2 Benzene has a solubility of 1750 ppm, and a specific gravity of 0.873. The aquifer ahs a porosity of 0.25, a hydraulic gradient of 0.004 and a hydraulic conductivity of 1000 gpd/f..
Determine the speed of the arrow after traveling from rest : A bowstring produces a force against a 2.0 oz arrow given by where a = 40 lbf, b = 3.2 ft-1 and x is in ft. x = 0 when the arrow is pulled fully back and increases as the arrow moves forward. Determine the speed of the arrow after traveling from rest..
Calculate the power rating of the electric heater required : A room 7m x 6m x 3m high is to be electically heated to maintain the inside temperature at 20 C, when it is 0 C outside. The room has 2 windows each 1.2m x 1.8m and a sliding glass door 2.4m x 2.1m. The transmission coefficients u in Wm^2/C are given..
What input of power rating is required for the pump : A water storage tank located on a larege dairy farm has a storage capacity of 0.1 ML. The average rate of water consumption from this tank is 6.25 kL per day, every day.
What temperature will the chip be operating at when the fan : An electronic chip internally generates 1.5 Watts of heat energy that must be dissipated to ensure its reliable operation. A fan, with an exposed area of 10cm^2 is attached to the chip so the heat can be transferred away by convection.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Fundamentals of hydraulic engineering

A stabilization pond is designed for a 35-day detention time. If the pond is maintained at a capacity of 40 acre-feet, what is theaverage gpd flow to the stabilizaiton pond?

  Describe the water surface profiles at the various parts

.Water enters a very wide rectangular channel (Manning’s n = 0.0149) at a velocity of 12.2 ms-1 and a depth of 0.61 m. An H3 curve forms downstream and the water jumps to a depth of 2.4 m some distance downstream. Find the distance downstream to the ..

  Calculate number-average molecular weight of random nitrile

Calculate the number-average molecular weight of a random nitrile rubber [poly(acrylonitrile- butadiene) copolymer] in which the fraction of butadiene repeat unit is 0.30

  Which reactor is more efficient and why

There are three reactors degrading a chemical biologically, at three degradation rates; i.e., 0.2 d^-1, 0.4 d^-1, and 1.0 d^-1. The residence time of the chemical in these reactors are 10 d, 5 d, and 55 d, respectively

  How much could he exert if he moved his hands to the ends

A plumber places his hands 18 inches apart on a pipe threader and can push (and pull) with 80 lb of force. What couple moment does he exert? How much could he exert if he moved his hands to the ends so that his hands are 254 inches apart?

  Plot the two test results on a shear stress-normal stress

At a confining pressure of 2000 psi, the first sample failed at 9000 psi. Then at a confining pressure of 5000 psi, the other sample failed at 21,000 psi. Plot the two test results on a shear stress-normal stress diagram and draw in Mohr envelope.

  Calculate the work necessary to compress air in cylinder

Calculate the work necessary to compress air in an isolated cylinder from a volume of 6 ft^3 to a volume of 1.2 ft^3. The initial pressure and temperature are 30.0 psia and 50 degree F, respectively.

  Should the company proceed with the process change

The company Eco-Safe is adding pollution control equipment to its process and reducing emission of pollutants. The annual waste disposal cost of the current process is $130,000 and the annual operating cost is $600,000

  Principle of lateral continuity

Would you expect to find the Tapeats Sandstone on top of the Great Unconformity in all places in the Grand Canyon? Why, or why not?

  Principal stresses and the orientation of planes

A direct shear test is performed on a saturated specimen of loose sand. A normal stress equal to 100 kPa is applied and a maximum shear stress of 75 kPa is measured in the shear test. Determine the principal stresses and the orientation of these p..

  Determine volumetric flow rate in head across the turbine

The blade height is 1.0 m, and the inlet radius of the rotor is 7.0 m. The flow exits the turbine in a radial direction. (a) If the angle between the radial direction and the absolute velocity at the inlet is 30o

  What is the highest possible design speed for the curve

design a horizontal curve for a two lane road. The road has 12 ft. lanes. Due to expensive excavation, it was determined that a maximum of 34 ft. can be cleared from the roads centerline towards the inside lane to provide for stopping sight distan..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd