How fast will the electron be moving when it reaches surface

Assignment Help Chemical Engineering
Reference no: EM13963437

1. On planet Tehar, the free fall acceleration is the same as that on Earth but there is also strong downward electric field with the field being uniform close to the planet's surface. A 2.00 kg ball having a charge of 5.00 mC is thrown upward at a speed of 20.1 m/s and it hits the ground after an interval of 4.10 s. What is the potential difference between the starting point and the top point of the trajectory?

2. An electron starts from rest 3.00cm from the center of a uniformly charged sphere of radius 2.00cm. If the shpere carries a total charge of 1.00 * 10^-9C, how fast will the electron be moving when it reaches the surface of the sphere?

3. A certain storm cloud has a potential difference of 1.00 * 10^8V relative to a tree. If, during a lightning storm, 50.0C of charge is transferred through this potential difference and 100% of the energy is absorbed by the tree, how much water(sap in the tree) initially at 30.0degreeC can be boiled away? Water has a specific heat of 4186J/kg degreeC, at boiling point of 100 degreeC, and a heat of vaporization of 2.26 * 10^6J/kg

4. A plastic pellet has a mass of 7.5*10^-10kg and carries a charge of 2.00 *10^-9C. The pellet is fired horizontally between a pair of oppositely charged paralled plates, as shown in the attachment, If the electric field strength between the plates is 9.2*10^4N/C and the pellet enters the plates with an initial speed of 150m/s, determine the deflection angle &. (hint this is similar to those involving the motion of a projectile under gravity)

Reference no: EM13963437

Questions Cloud

Employers do not pay payroll taxes on payments : Employers do not pay payroll taxes on payments made to independent contractors The FICA tax rates and taxable wage bases are exactly the same for employees and employers
What is the final total mass of the cup and its contents : A 150 gram Aluminum calorimeter cup contains 320 grams of water at 22 degrees Celsius. Steam at 100 degrees Celsius is routed into the calorimeter until the temperature of the cup and its contents reaches 50 degrees Celsius.
Partial and total functions : For each of the following function de?nitions, give the graph of the function. Say whether this is a partial function or a total function on the integers. If the function is partial, say where the function is de?ned and  unde?ned.
Write a program that prompts the lowest temperature : Write a program that prompts the user for the lowest and highest Fahrenheit temperature wanted in the table, and also prompts the user for the desired step size between rows of the table.
How fast will the electron be moving when it reaches surface : What is the potential difference between the starting point and the top point of the trajectory?
What is buzz marketing and guerrilla marketing : What is buzz marketing? What is guerrilla marketing? How does it differ from traditional marketing? What is geocoding? Define lifetime value. How is it determined
Location vacuum world under murphy law : Consider the accessible,two-location vacuum world under Murphy's Law. Show that for each initial state, there is a sequence of actions that is guaranteed to reach a goal state.
Levels of firewall development : 1. Which of these is the one thing an organization cannot survive without? 2.Which of the following is an anti-spam control?3.Which of the following levels of firewall development includes stateful inspection?
Describe examples of the different types of norms operative : Compare and contrast culture, popular, high culture, elite culture, mass culture, low culture, subculture and counterculture. Describe examples of the different types of norms operative in popular culture, and how these are related to the process of..

Reviews

Write a Review

Chemical Engineering Questions & Answers

  Maximum allowable stress

The vessel is 4 m internal diameter and 20 m long. Estimate the minimum wall thickness required to resist this pressure, for the cylindrical section and the heads. Take the design pressure as 12 bar and the maximum allowable stress for the materia..

  Maximize recovery of condensable components

a. How many design variables must be specified in order to calculate the output stream compositions and flow rates? b. How would you optimize these variables if the objective of the separator was to maximize recovery of condensable components into ..

  Find the ratio of the latent heat of fusion of the particle

Derive an equation for the latent heat of fusion that is a function of the radius of the particle. Using this equation, for a copper particle that has a radius of 2.5 nm, find the ratio of the latent heat of fusion of the particle to the laten..

  What concentration of phosphorus

What concentration of phosphorus (P) would you expect at the top of the boule (X=0)? If the boule is 1 m long and has a uniform cross section,at what position (or Xvalue)would you expect the concentration of phosphorus to be twice as large as it is..

  Determination of the discharge coefficient of the orifice

This is a fluid dynamics experiment involving the filling and emptying of tanks. The objectives of the experiment include: Determination of the discharge coefficient of the orifice and the equivalent length of a pipe mounted at the outlet of the two..

  Mining and metallurgy - assignment metallurgy

Extract ore descriptors or features from the variables and design a model that can classify the ores correctly from images of the ore

  Formation of a white precipitate

When dilute nitric acid was added to a solution of one of the following chemicals, a gas was evolved, This gas turned a drop of limewater, Ca(OH)2, cloudy, due to the formation of a white precipitate. The chemical was

  Why did experts recommend grounding these tanks and storing

the paint formerly used on some storage tanks contained aluminum powder which reflected heat from the surface of the

  Materials of construction for the tanks

Plain carbon steel would be a suitable material for the tanks, but it is essential that the polymer does not become contaminated with iron in storage. Suggest some alternative materials of construction for the tanks.

  Concentration of original hydrochloric acid solution

A 25.00-mL sample of hydrochloric acid solution requires 24.16 mL of 0.106 M sodium hydroxide for complete neutralization. What is the concentration of the original hydrochloric acid solution?

  Eliminate differences in composition

Eliminate Differences in composition and eliminate differences in temperature, pressure and phase

  Value and direction of a single resultant force

Determine mathematically the value and direction of a single resultant force which when acting upon the plate shown below would effectively replace the forces shown.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd