Hot water is provided to a house by electric water heater

Assignment Help Mechanical Engineering
Reference no: EM13710344

Hot water is provided to a house by an electric water heater which uses a 60L tank. The electric heater is rated for a 1.6kW. The hot water tank is completely full with water at 80°C when someone starts a shower. The shower faucet mixes cold water at 20°C and a flow rate of 0.06kg/s with hot water at an unknown flow rate from the water heater. After an 8min shower period, the water in the hot water heater has dropped to a temperature of 60°C. The heater ran continuously during the shower period and drew in cold water at 20°C at the same rate as hot water left it. What was the mass of hot water withdrawn from the tank?

Reference no: EM13710344

Questions Cloud

Personal health records concept in an organisation : How is Personal Health Records utilised in other organisations and what are the risks and what experiences are gained by other companies in using Personal Health Records
Determine specific enthalpy and velocity at exit of valve : Steam flows at steady state through a well-insulated pressure-reducing valve. At the inlet, the pressure is 4 MPa, the temperature is 320°C, and the velocity is 60 m/s. The pressure of the steam at the exit is 700 kPa.
Derive laplace transform by integration from basic integral : Derive Laplace transform by integration from basic integral definition. Do not use laplace transform tables or associated theorems. Refer to standard integral tables.
Review or appraisal based on careful analytical evaluation : Your analysis should explore the positives and negatives in each case and reach a balanced view of the strengths and weaknesses of the person you have selected.
Hot water is provided to a house by electric water heater : Hot water is provided to a house by an electric water heater which uses a 60L tank. The electric heater is rated for a 1.6kW. The hot water tank is completely full with water at 80°C when someone starts a shower. The shower faucet mixes cold water at..
What is the annual after-tax cost of debt : What is the annual after-tax cost of debt to the company on this issue and how much must the assets be reduced to bring the TATO to the industry average - what is the project's IRR?
What is final temperature and assume process is adiabatic : An evacuated 1-ft3 tank is connected by a valve to a nitrogen supply line flowing air at 120 psi and70oF. A valve is opened allowing air to flow into the tank until the pressure reaches 90 psi. How much mass flowed into the tank and what is its final..
Consider the variation of specific heat with temperature : A gas turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 7. Determine the back work ratio of this cycle, if the temperature of air at the compressor and the turbine inlet are 300 K and 1300 K respectively. (Consider the v..
Determine the radius of curvature of the particle path : A particle which movies in a two-dimensional curvilinear motion has coordinates in millimetres which vary with time t in seconds according to x=5t2 +4 and y=2t3 + 6. For time t =3s, determine the radius of curvature of the particle path and the magni..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  When being chargerd by a 40 volt dc supply find the time t

given that the instantaneous voltage across a capacitor isvc401-e-tcrvoltswhen being chargerd by a 40 volt dc supply

  Aluminium foil for household use is nearly pure aluminium

Common aluminium foil for household use is nearly pure aluminium. A box of this product at a local supermarket is advertised as giving 69ft2 of material (in a roll 304 mm wide by 21.0 m long). If the foil is 0.3mil (7.62 μm) thick, calculate the num..

  Hydrogen at 25 bar 450degc enters an adiabatic turbine and

hydrogen at 25 bar 450degc enters an adiabatic turbine and expands to 2 bar 160degc with a mass flow rate of 0.2 kgs.

  When operating at 35c and 101 bars at take-off conditions

the following data apply to the auxiliary power unit apu on the boeing 777 single-shaft unit driving separate load

  Piston on the air during the compression stroke

At the beginning of the compression stroke, the volume of a certain diesel engine cylinder is 1.000 liter and it is filled with air at 300 K and 100 kPa absolute. At the end of the compression stroke the air is at 800 K and 4280 kPa absolute.

  The friction between the bed of the truck and the cylinder

a solid cylinder of radius r and mass m is initally at rest on the bed of a truck. the distance from the center of the

  Air conditioning1- cooling and heating load estimate using

air conditioning1- cooling and heating load estimate using camel program library and the data from da-9 perform a

  Consider the flow of air over a vertical flat plate at a

consider the flow of air over a vertical flat plate at a low velocity u1 in ambient pressure p1. the plate surface

  Water flows in a 5-m-wide channel with a speed of 2 ms and

water flows in a 5-m-wide channel with a speed of 2 ms and a depth of 1m. the channel bottom slopes at a rate of 1 m

  Knowing that timber of 4-in nominal width 935-in actual

a 12-ft-long overhaning timber beam ac with an 8-ft span ab is to be designed to support the distributed and

  Discuss whether the following situations should be modeled

discuss whether the following situations should be modeled as closed systems or open systems. clearly define the

  A steel wide flange beam w14 x 26 carries the load compute

a steel wide flange beam w14 x 26 carries the load. compute the maximum deflection between the supports and at each

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd