User Account

All Pages

High-speed elevator problem

Assignment Help Mechanical Engineering
Reference no: EM13703888

A high-speed elevator is being designed that must be able to travel at a maximum speed of 11.5 fts. You are asked to recommend the lift motor to use. The completely furnished carriage will have a mass of 3500 pounds. The design occupancy limit will be eight people weighing an average of 200 pounds. Since there will always be some unknowns in the actual operation of the elevator, use a Factor of Safety of 2. In other words, recommend a motor that has exactly twice the power rating needed (based on all the design limit specifications). How big of a motor, in hp, should you recommend?

Reference no: EM13703888

Questions Cloud

Describe the four main investment appraisal methods : List and describe the four main investment appraisal methods. Which one is the best method to evaluate a risky investment and why - What are the sources of finance for a limited company
What is the absolute pressure in the pressure vessel : Consider the manometer attached to this pressure vessel as shown. If the manometer fluid is mercury (density=13,600 kgm3), and the height of the fluid (h) is 3.9 cm, then what is the absolute pressure (P) in the pressure vessel in kPa?
Converts the rotation of the impeller into water pressure : An electric motor converts electricity to rotating shaft work with an efficiency of 54%. The rotating shaft turns the impeller in the pump which, in turn, increases the pressure of the water (i=1000kg/m3) by 200 kPa. If the motor is consuming 3.5 kW ..
What is the mechanical efficiency of the pump : Pumps are generally used to increase the pressure of a liquid. This is done by converting rotating shaft work (within the pump) into mechanical energy (of the liquid). Within such a pump, the energy of the liquid is being increased by 4.95 kW, while ..
High-speed elevator problem : A high-speed elevator is being designed that must be able to travel at a maximum speed of 11.5 fts. You are asked to recommend the lift motor to use. The completely furnished carriage will have a mass of 3500 pounds. The design occupancy limit will b..
The crystal structure of iron is bcc at temperatures : The crystal structure of iron is BCC at temperatures below 912°C and FCC above 912°C. Calculate the weight of one unit cell of iron (a) below 912°C; (b) above 912°C.
Combustion in a cylinder causes the pressure to increase : Combustion in a cylinder causes the pressure to increase, which moves the piston a distance (x) of 7 inches. The piston is held in place by a spring ( k=60lbfin) that was at its relaxed length before the combustion process. How much work did the expa..
How much energy was transferred to the room : You arrive home from a winter trip and turn on your baseboard (resistance coil) heater to warm the room. It remains on for 14 minutes, during which time it steadily consumes 3.5 kW of electricity. How much energy was transferred to the room in kJ?
Goal definition and performance indicators in soft projects : Goal Definition and Performance Indicators in Soft Projects - Describe one specific example of good project planning in the project.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the heat transfer coefficient for laminar flow

Determine the heat transfer coefficient for laminar flow over this cylinder. First, at your discretion, select an available set of experimentally obtained data from the literature. Then, this would provide you with a set of Reynolds numbers.

  At the inlet the velocity is 40 fts and the pressure 15

liquid water flows isothermally at 75of through a one-inlet one-outlet duct operating at steady state. the ducts inlet

  What is the angular acceleration of the turntable assuming

the turntable of a record player rotates initially at the rate 33 revmin and takes 14.07 s to come to rest. what is the

  A steam turbine is limited to a maximum inlet temperature

a steam turbine is limited to a maximum inlet temperature of 800degc. the exhaust pressure is 0.0100 mpa and the

  Determine the mass flow rate

(a) Draw and label a schematic of the system. (b) Determine the mass flow rate (kg/s) of water vapor neededand (c) the rate of exergy destruction (kW)

  Ammonia enters the expansion valve of a refrigeration

ammonia enters the expansion valve of a refrigeration system at a pressure of 10 bar and a temperature of 248c and

  The cable supporting the elevator has a design load of

an elevator weighing 1000lb is carrying a load of 500 lb and descending at 20 fts. the cable supporting the

  Determine the rate of heat loss per square meter of the

thermopane window consists of two 6 -mm thick glasses separated by a stagnant air space of thickness 6 mm. the thermal

  Determine the exit temperature of the helium

Helium at 800kPa, 600C enters a steady flow turbine and leaves at 100kPa. The helium undergoes an expansion process through the turbine, does work in the amount of 900kj/kg, and loses 50kj/kg of energy by heat transfer to the surroundings.

  Consider a 1000-w iron whose base plate is made of

consider a 1000-w iron whose base plate is made of 0.5-cm-thick aluminium alloy 2024-t6 p2771 kgm3 and cp 875 jkg c.

  Taking the object and liquid as a system how much word the

a 4 kg object traveling at 60 ms enters an insulated vat of 20 kg of incompressible fluid c 2.0 kjkgk and comes to

  Plastics and other polymeric materials are expensive with

plastics and other polymeric materials are expensive with respect to steel and are usually more costly than aluminum

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd