Helium gas is contained in a rigid vessel

Assignment Help Mechanical Engineering
Reference no: EM13707399

Helium gas is contained in a rigid vessel of 0.5 m3 at 500 kPa. The gas is agitated violently by a stirrer that transfers 250 kJ of work to the gas. Assuming that the system undergoes an adiabatic process, determine the final pressure of the gas. Assume that Cv for helium is a constant at 12.46 kJ/kmol·K.

Reference no: EM13707399

Questions Cloud

A piston-cylinder device contains helium gas : A piston-cylinder device contains helium gas initially at 145 kPa, 20 degrees C, and 0.5 m^3. The helium is now compressed in a polytropic process (PV^n = constant) to 400 kPa and 140 degrees C. Determine the heat loss or gain during this process.
Ice forms on a duct transporting liquid nitrogen : Ice forms on a duct transporting liquid nitrogen. The duct consists of a circular hole, with diameter D=0.5 m, surrounded by square insulation, width=0.95 m, and thermal conductivity k=0.223 W/m*K. The inside of the duct is maintained at the boiling ..
Elevator starting from rest accelerates : If an elevator starting from rest accelerates at 10m/s and then decelerates at -1m/s until it reaches the top floor (ignore gravitational acceleration, assume g=0. Plot the corresponding a-t, v-t and s-t graphs.
Determine the initial volume of the cylinder : A mass of 0.5 g of air is contained in a piston-cylinder device. Initially the system is at 100 kPa and 25°C. The system is now compressed adiabatically to a volume 17 times smaller and a temperature of 700 K.
Helium gas is contained in a rigid vessel : Helium gas is contained in a rigid vessel of 0.5 m3 at 500 kPa. The gas is agitated violently by a stirrer that transfers 250 kJ of work to the gas. Assuming that the system undergoes an adiabatic process, determine the final pressure of the gas. Ass..
What is the internal energy of the gas after the expansion : The amount of heat (dh = 327.18 KJ) is added to an open volume of 1m3 of air (at standard sea level conditions), causing it to expand to 4 m3. How much work is done by the air? What is the internal energy of the gas after the expansion?
Determine the heat transferred to and the work produced : Steam at 75 kPa and 13 percent quality is contained in a spring-loaded piston-cylinder device, as shown in the figure, with an initial volume of 5.28 m^3. Steam is now heated until its volume is 13.20 m^3 and its pressure is 300 kPa. Determine the he..
What equivalence ratio for octane-air mixtures : At what equivalence ratio for octane-air mixtures does the carbon to oxygen ratio of the system equal one? Why is this of interest?
Maximum shearing stress in cylinder after-internal pressure : A laminated thick-walled cylinder was fabricated by shrinking a steel (E=200 GPa and nu=0.03) sleeve having an inside diameter of 199.800mm and an outside diameter of 300mm onto a steel tube with an inside diameter of 100mm and an outside diameter of..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Employing the ideal gas model and ignoring potential energy

air enters an insulated diffuser operating at steady state at 1 bar -3 degrees c and 260 ms and exits with a velocity

  A surface area of 15 m2 find the final volume of the argon

a rigid tank of volume 6 m3 contains argon at 500 kpa 30oc. it is connected to a piston cylinder initially at the

  A container of air with a fixed volume of 1 ft3develops a

a container of air with a fixed volume of 1 ft3develops a slow leak. the container originally is at 900 degrees at

  A flange is used for instrument connection for a system

a flange is used for instrument connection for a system with a design temperature of 316degc 600degf and a design

  The air flow is 05 kgs in a 10 cm diameter pipe find the

a counter flow heat exchanger is used to cool air at 540 k and 400 kpa to 360 k using a 0.05 kgs supply of water at 20

  Probabilistic hough transform in big o notation

Probabilistic Hough transform in big O notation

  What is the flow rate required to cool and maintain

what is the flow rate required to cool and maintain 0.5 x 0.5 x 0.5 m3 volume of air at 297 K to 199 K, using nitrogen at 199 K

  Calculate the force required in direct extrusion

Calculate the force required in direct extrusion of 1100-O aluminum from a diameter of 6 in. to 2 in. Assume that the redundant work is 30% of the ideal work of deformation, and the friction work is 25% of the total work of deformation.

  Determine the tensions developed in wires

Determine the tensions developed in wires , and and the angle required for equilibrium of the 30-lb cylinder E and the 60-lb cylinder F.

  A velocity field is described by the equation given below

a velocity field is described by the equation given below with a 3 m2 s2 and b 4 m3. determine the equation of the

  What if the 820 kg car actually moves backwards with a

an 1640 kg car stopped at a traffic light is struck from the rear by a 820 kg car. the two cars become entangled moving

  The magnitude of the absolute velocity at the pump exit is

the radial component of velocity of water leaving the centrifugal pump sketched in figure is 30 fts. the magnitude of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd