Given temperature of the hot loop tin3670c tout73738c hot

Assignment Help Mechanical Engineering
Reference no: EM13641022

Given: temperature of the hot loop Tin=36.70C Tout=73.738C, Hot flow: 2.985 gal/min temperatures of the cold loop Tin= 14.42C Tout=36.37C Cold flow: 5.128 gal/min. Fuel burn rate is at 0.07 kg/min.

Q=mcp(Tout-Tin)+W

Find:
a) amount of heat produced by furnace
b0 amount of heat generated by ideal combustion of fuel.

Reference no: EM13641022

Questions Cloud

There is no heat transfer between the heater and the : a contact feedwater heater operates on the principle of mixing steam and water. steam enters the heater at 100 psia and
A sprinter explodes out of the starting block with an : a sprinter explodes out of the starting block with an acceleration of 4.5 ms2 which she sustains for 1.5 s. then her
Assume you have one hydrogen molecule in a 100 l flask at : assume you have one hydrogen molecule in a 1.00 l flask at room temperature. calculate the average energy of the h2
A fast food center wishes to estimate the proportion of : a fast food center wishes to estimate the proportion of people in its city that will buy its products. suppose the true
Given temperature of the hot loop tin3670c tout73738c hot : given temperature of the hot loop tin36.70c tout73.738c hot flow 2.985 galmin temperatures of the cold loop tin 14.42c
A physicist out at the cabin uses a sonar device to : a physicist out at the cabin uses a sonar device to determine the speed of a jet-ski on the nearby pond. a 20.5 khz
If the total pressure in the container is 500 atm what are : 1 mole of oxygen gas o2 and 2 moles of ammonia nh3 gas are placed in a container and allowed to react at 850 c
When the three blocks are released from rest they : when the three blocks are released from rest they accelerate with a magnitude of 0.600 ms2. block 1 has mass m block 2
The brewing industry uses yeast microorganisms to convert : the brewing industry uses yeast microorganisms to convert the glucose c6h12o6. to ethanol c2h5oh for wine and beer. the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Derive the mathematical expression of the displacement as a

mass 8kg stiffness 90nm initial displacement 0.1m initial velocity 0.9ms assume the system is critical damped. find the

  What is the atmospheric pressure at that altitude if the

a pilot flying a new airplane reports that she is flying at 49000 ft as read on her altimeter that is referenced to

  Etimate the temperature inoc to which the block must be

at room temperature 23oc a cylinder of steel has a diameter of 15.02 mm which is too large to fit into a 15 mm diameter

  Briefly explain why porosity decreases the thermal

briefly explain why porosity decreases the thermal conductivity of ceramic and polymeric materials rendering them more

  Estimate the percentage of fabric samples that will have a

data analysis of the breaking strength of a certain fabric shows that it is normally distributed with a mean of 300 lb

  Locate the centroid x and y of the cross sectional area

locate the centroid x and y of the cross sectional area and then determine the orientation of the principle axes which

  Complete the sketch of the obtuse triangle

Complete the sketch of the obtuse triangle. It must have an area of 1.75 in.2. Prove the geometry by dimensioning the sketch and showing the area calculation. Show only those dimensions needed for the area calculation. Note: each grid unit = .25 i..

  Determine the power input hp and heat transfer rate btumin

helium gas is compressed reversibly from 16 psia and 85 degree f to 120 psia. the helium enters the compressor with a

  Calculate the moid constant b then compute the

a rectangular casting having the dimensions 3 inch by 5 inch by 10 inch solidifies completely in 11.5 min. using n2 in

  A simple ideal brayton cycle with air as the working fluid

a simple ideal brayton cycle with air as the working fluid has a pressure ratio of 11. the air enters the compressor at

  Hot exhaust gases carbon dioxide are cooled from 700 k to

hot exhaust gases carbon dioxide are cooled from 700 k to 300 k isobarically at 500 kpa. the cooling fluid is

  A container of diamer 6cm and height 10cm is filled with

a container of diamer 6cm and height 10cm is filled with water 7cm high in the container.a at which rotation speed will

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd