Fused deposition modeling is used to fabricate

Assignment Help Mechanical Engineering
Reference no: EM13718167

"(USCS units) fused deposition modeling is used to fabricate a part which is a model of the step pyramid at Sakkara in Egypt (built circa 2670 BCE). The model has six levels or steps, each with a thickness of 0.17 in. The bottom layer = 2.20 in on a side, and successive levels are 1.85, 1.50, 1.15, 0.80, and 0.45 in on a side, respectively. Height of the pyramid = 1.02 in. In the FDM process, layer thickness = 0.010 in and the width of the extrudate deposited on the surface = 0.025 in. The extruder head moves in the x-y plane at a speed of 10 in/sec. A delay of 12 sec is experienced between each layer to reposition the worktable. Compute an estimate for the time required to build the part. Setup time = 35 min. Ignore post-processing time. Using the time estimated to build the part, determine the part cost (in $) if the ABS polymer used in the process costs $9.50/lb and its density = 0.038 lb/in^3, machine hourly rate = $8.00/hr, and labor rate = $30.00/hr but labor will be used only 40% of the build time, mostly for setup."

Reference no: EM13718167

Questions Cloud

How much rtcp bandwidth particular sender will be allocated : What rate RTCP will limit its traffic to and how much RTCP bandwidth a particular sender will be allocated?
Heat pumps and refrigerator operated with reversible cycle : Find the temperature of water at 200 kPa and specific enthalpy of 350 kJ/kg. A heat pump and a refrigerator operate on same cycle between same hot and cool reservoir at temperature TH, and TL, respectively. Please demonstrate = +1 COPHP COPRF and com..
Compute the required heat transfer : Refrigerant 134a is contained within a rigid tank at an initial state of 2.8 bar and 100 C. Heat is removed until the pressure drops to 2.4 bar. compute the required heat transfer
What is the work done on the ball by air resistance : A basketball player makes a jump shot. The 0.560-kg ball is released at a height of 1.80 m above the floor with a speed of 7.07 m/s. What is the work done on the ball by air resistance
Fused deposition modeling is used to fabricate : "(USCS units) fused deposition modeling is used to fabricate a part which is a model of the step pyramid at Sakkara in Egypt (built circa 2670 BCE). The model has six levels or steps, each with a thickness of 0.17 in. The bottom layer = 2.20 in on a ..
Determine the percentage excess reactant : If 500 lbm/hr NH3 and 4000 lbm/hr air (note air, not O2) are mixed to produce 600lbm/hr NO, Determine the percentage excess reactant
Estimate which bullet will hit the ground first : You fire a bullet from a height of 50m with a horizontal velocity of 50 m/s to the right. Which bullet will hit the ground first
Find how far from the earth surface must the spacecraft be : When a spacecraft travels from the Earth to the Moon, both the Earth and the Moon exert a gravitational force on the spacecraft. How far from the Earth's surface must the spacecraft be
Find the ratio of the coulomb and gravitational forces : Calculate the ratio of the coulomb and gravitational forces between two protons. How does this ratio vary with the distance between them

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the mass flow rate and the exit flow area

Air enters a one-inlet, one-exit control volume at 6 bar, the pressure is 3 bar, the temperature is 456.5 K, and the velocity is 300 m/s. The air behaves as an ideal gas for steady-state operation, determine: (a) the mass flow rate in kg/s (b) the ex..

  Nitrogen at 900kpa and 300oc is expanded adiabatically and

nitrogen at 900kpa and 300oc is expanded adiabatically and reversibly in a closed system to 100kpa. determine the

  Air at 2900 r 435 psia enters a turbine operating at steady

air at 2900 r 435 psia enters a turbine operating at steady state and expands adiabatically to the exit where the

  The mass of each pulley of the system is m and the mass of

the mass of each pulley of the system is m and the mass of the suspended object a is ma. determine the force t

  Two previously undeformed cylindrical specimens of an alloy

two previously undeformed cylindrical specimens of an alloy are to be strain hardened by reducing their cross-sectional

  A long pryoceram rod with a diameter of 08m is clad with a

a long pryoceram rod with a diameter of .08m is clad with a very thin metallic tube for protection. the bonding between

  A piston-cylinder arrangement holds a thermally perfect gas

A piston-cylinder arrangement holds a thermally perfect gas at p1=100kPa and T1 = 300K. Assume that cp = 1.0035 kJ/kg-K, cv = 0.7165 kJ/kg-K, and R = 0.287 kJ/

  Find the maximum static load corresponding to the yield

a helical compression spring is made of no. 18 .0147 in wire having a torsional yield strength of 108 kpsi. it has an

  A 1050 hot-rolled steel of diameter 300mm has an ultimate

a 1050 hot-rolled steel of diameter 300mm has an ultimate tensile strength of sut724mpa that is hot-rolled is exposed

  This unit cell is similar to the face-centered cubic unit

consider the cuau crystal structure. it can be described as a simple cubic lattice with a basis of cu 0 0 0 cu 1 2 1 2

  A vehicle is to be propelled by a jet of water inclined 15

a vehicle is to be propelled by a jet of water inclined 15 degrees impinging on a vane as shown in figure 16.16. the

  A motorcycle starts from rest at t 0 and travels along a

a motorcycle starts from rest at t 0 and travels along a straight road with a constant acceleration of 5 fts2 until it

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd