For a concrete column that is part of a braced frame

Assignment Help Civil Engineering
Reference no: EM13560455

For a concrete column that is part of a braced frame, if the column is square, tied, 18 inches per side, 16 feet long, classify the column as slender or non slender. Assume that at one end of the column a clockwise moment of 100 k-ft is present, and that at the other end of the column a counter-clockwise moment of 25 k-ft is present. you may assume that k= 1.

Reference no: EM13560455

Questions Cloud

Calculate the steady state hcho concentration : These concentrations were measured when the trailers were 2 years old and the emission rate had significantly decreased by that time. New material rates as high as 290 mg/hr have been reported. Calculate the steady state HCHO concentration (ug/m3) re..
How efficient is the pump : A fireboat pump draws seawater (density=1.95 slugs/ft^3) from a 6 inch diamter submergred pipe that reaches 6 feet under the free surface and discharges 120 ft/s through a 2 inch diamter nozzle 10 feet above the free surface
Find the rate of biological growth : Two identical complete-mix activated sludge units are connected in series; one-half of the sludge recycle flow rate, QR, is recycled to the primary effluent pipeline which handles a flow rate Q, and the other half is recycled to the effluent line fro..
Which alloy and in what condition whould you choose : For a concrete column that is part of a braced frame, if the column is square, tied, 18 inches per side, 16 feet long, classify the column as slender or non slender
For a concrete column that is part of a braced frame : For a concrete column that is part of a braced frame, if the column is square, tied, 18 inches per side, 16 feet long, classify the column as slender or non slender. Assume that at one end of the column a clockwise moment of 100 k-ft is present
Which cross section option will provide the highest flow : Two channel cross sections are proposed. Assume slope, cross sectional area, and surface type are constant for each channel. Which cross section option will provide the highest flow rate? Show calculations.
What is the major head loss in a coarse concrete pipe with : What is the major head loss in a coarse concrete pipe with a diamter of 1ft that is 100 ft long. Water flows at a rate of 20 ft^3/s (viscosity of water = 2.344x10^-5 lbfs/ft^2, density of water = 1.94 slugs/ft^3) 1inch = 25.4mm
What is the major head loss in a coarse concrete pipe with : What is the major head loss in a coarse concrete pipe with a diamter of 1ft that is 100 ft long. Water flows at a rate of 20 ft^3/s (viscosity of water = 2.344x10^-5 lbfs/ft^2, density of water = 1.94 slugs/ft^3) 1inch = 25.4mm
Classify the column as slender or non slender : For a concrete column that is part of a braced frame, if the column is square, tied, 18 inches per side, 16 feet long, classify the column as slender or non slender

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the average time that a passenger must wait for the

Each of two buses carries passengers from a depot to various destinations and return for another trip with a round trip time very nearly equal to R

  The campus would like to recoup the total construction cost

A parking facility on a campus was recently opened to faculty,staff and students.It cost a total of $ 300,000 to construct the facility. It is expected that thefacility will require no maintenance for the first 2 years ofoperation.At end of year 3, t..

  What will be the discharge

A concrete sewer pipe 1m in diameter is laid so it has a drop in elevation of 30cm per 300m of length. If sewage (assume the properties are the same as those of water) flows at a depth of 50cm in the pipe, what will be the discharge?

  Describe what design speed was used for the curve

Lane widths are 12ft and the superelevation is .006 and was set assuming maximum fs. If the necessary sight distance required 52ft of lateral clearance from the roadway center line, what design speed was used for the curve

  What is the water-balance estimate of the lake evaporation

Measurements of water-balance components have been made for a one-year period on a lake with an area of 4.4 km2 with the following results: P = 350 mm, Qsi = 2.33 x 107 m3, Qgi = 2.2 x 105 m3, Qgo = 0.6 x 105 m3, and Qso = .10 x 107 m3.

  Compute the magnitude of the load that is necessary

An alloy has a yield strength of 41 ksi, a tensile strength of 57 ksi, and an elastic modulus of 16 X 10^6 psi. A cylindrical specimen of this alloy 0.5 in in diameter and 10 in long is stressed in

  Find range of values of theta for which both cables are taut

A worker ties a rope oflength 12 m to he tower at A and exerts a constant force of 160 Non the rope. (a) Express the tension in each cable as a function oftheta knowing that the resultant of the tension in the cables andthe rope is directed downwa..

  What is the maximum length to which it may be stretched

what is the maximum load that may be applied to a specimen with a cross sectional area of 130 mm^2 without plastic deformation.

  Determine change in the bottom elevation and water surface

A hydraulic transition 100 ft long is used to connect two rectangular channels, 12ft and 6ft wide. The design discharge is 500 cfs, mannining coefficient=.013 and the slopes of the channels are both .0009.

  What would the concentrationin the effuent be 7 days later

A lagoon with a volume of 1200 m^3 has been receiving a steady flow of a conservative waste at a rate of 100m^3/day for a long enough time to assume that steady-state conditions apply. The waste entering the lagoon has a concentration of 10mg/L.

  How to use the bisection method on the vander wals

How to use the bisection method on the van der waals equation Problem The van der Waals equation gives a relationship between the pressure P (in atm.),

  Consider the steady viscous flow through a small horizontal

Consider the steady viscous flow through a small horizontal tube. for this type of flow, the pressure gradient along the tube should be a function of the dynamic viscosity, the mean velocity and the diameter of the tube. use dimensional analysis to d..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd