Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.The bucket of the front-end loader shown carries a 3200-lb load. The motion of the bucket is controlled by two identical mechanisms, only one of which is shown. Knowing that the mechanism shown supports one-half of the 3200-lb load, determine the force exerted (a) by cylinder CD, (b) by cylinder FH.
2.Flow occurs in a rectangular channel of 6 m width and has a specifi c energy of 3 m. Plot the q-curve. Determine from curve (a) critical depth (b) the maximum flow rate (c) the flow rate at a depth of 2.4 m and (d) the depths at which flow rate of 28.3 m^3/s may exist and the flow conditions at these depths.
A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E=29x10^6 psi, α=6.5x10^-6) and portion BC is made of aluminum (E=6.5x10^-6 psi, α=13.3x10^-6).
A piston-cylinder device contains 0.2kg of water initially at 800 kPa and 0.06m^3. Now 200 kJ of heat is transferred to the water while its pressure is held constant. Determine the final temperature of the water.
in an air standard otto cycle , the air at the beginning of the compression stroke is at 95 kpa and 22c ,and the cylinder volume is 0.0028 m^3 . the compression ratio is 9 and 4.3 kj are added during the heat addition process
A projectile is launched with an initial speed of 200m/s at anangle of 60degree with respect to the horizontal. compute thedistance "R" as measured up the incline.
A haul fleet of trucks having a heaped capacity of 15 cy. is to be loaded by a hydraulic backhoe excavator (CT=.48 min.) with a 3 1/2 cy. heaped capacity. Assume the material is a wet loam that weighs 3380 lb/cy in the bank state
To satisfy desige limitation it is necessary to determine the effect of the 2- kN tension in the cable on the shear tension and bending of the fixed I-beam.
Ignoring both axial and shear deformations and using the unit force method, calculate the vertical displacement of joint B.
What are the inputs needed to determine stress a polymer with a fixed end on one side, and the other with a tension force of 50,000 lbs a year after the load is applied?
A dam project specifies 97% compaction. Lab tests on the soil being used indicate that it has a maximum dry density of 1900 kg/m3 at an optimum water content of 13.2%. Field tests give the following results: Field dry density is 1790 kg/m3 and 16...
The specific yield of an unconfined aquifer is Sy = 0.15. How much, on average, would the water table need to be lowered (in m) in an area of 2.5 km^2 to release 6.5 x 10^5 m^3 of water from storage in this aquifer
The estimated uniform dead load for structural steel framing, firproofing, architectural features, floor finish and ceiling tiles equals 24 psf, and for mechanical duct, piping and electrical systems equals 6 psf.
a concrete test cylinder is loaded with p= 100k (445 kn) and resulting shortening of 0.036" (0.0914 mm). determine the unit strain developed in the concrete.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd