Find value of multiplier resistor to obtain full defection

Assignment Help Electrical Engineering
Reference no: EM13248998

An AC Voltmeter uses a bridge rectifier and 100 ohm PMMC which requires a 1mA DC current for full-scale deflection. Assuming ideal diodes, calculate the value of the multiplier resistor to obtain full scale deflection with 10 V AC applied to the input.

Reference no: EM13248998

Questions Cloud

Could a service firm use a production-line approach : Could a service firm use a production-line approach or self-service design and still keep a high customer focus (personal attention)? Explain and support your answer with examples.
Calculate the maximum value of r2 to compensate : A series type Ohmmeter uses a 50 ohm, 1mA PMMC the internal battery voltage is 3V the desired scale marking for half scale deflection is 2000 ohm. Calculate:- - Value of R1 & R2
Find the tension in each cable : A loudspeaker of mass 18.0kg is suspended a distance of h = 2.00m below the ceiling by two cables, What is the Tension T in each of the cables
Explain the solubility product constant ksp : The solubility product constant (Ksp) for the dissolution of SrSO4 as represented by the chemical equation is 2.5 x 10-7.
Find value of multiplier resistor to obtain full defection : An AC Voltmeter uses a bridge rectifier and 100 ohm PMMC which requires a 1mA DC current for full-scale deflection. Assuming ideal diodes, calculate the value of the multiplier resistor to obtain full scale deflection with 10 V AC applied to the i..
What kind of structure does the organization use : Explain the department you have chosen. This includes the name, mission, and goals of the department.
Calculate the potential difference between the two plates : Two plates of area 30.0 cm2 are separated by a distance of 0.0150 cm. calculate the potential difference (voltage) between the two plates
What frequency components will be obtained at the output : Given a sawtooth signal with fundamental frequency = 20 KHz as the input signal going into an ideal Highpass Filter with cutoff frequency fc = 60 KHz, what frequency components will be obtained at the output
Determine transfer function of 4th order lowpass filter : determine the transfer function of a 4th order lowpass butterworth filter with a 3-dB cutoff frequency of 3.4 kHz and passband gain=1. Design the circuit using MFB topology. Design two sections with an order of 2.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  State whether power factor is lagging or leading

The generator is delivering 48 MW to the bus bar at the rated voltage with its field current adjusted for a generated emf of 46 kV per phase. Determine the armature current and the power factor. State whether power factor is lagging or leading

  Calculate the required junction area of pn jucntion

A certain pn junction is operating with Vt=26mV and ni=1.08x10^10 electrons/cm^3. The doping concentrations are Na=2x10^15 cm^-3 and Nd=9x10^16cm^-3. The diffusion coefficient are Dn=34cm^2/s and Dp=12cm^2/s.

  Describe both mealy and moore state diagrams

We represent this by a non-overlapping sequence detector. In other words, asa soon as you detect the sequence, you will need to get another complete sequence to unlock. Therefore, you need to carefully choose to which state you will need to go.

  Determine the rated primary and secondary currents

A single phase transformer has the following rating: 120 kVA, 2000 V/100 V, 60 Hz with 1000 primary turns. Determine: (a) the secondary turns (b) the rated primary and secondary currents (c) the maximum flux

  What type of long-distance high-throughput wireless tech

The time has come for XelPharm to expand. The board of directors has purchased another warehouse for a second distribution facility. It's located in an industrial area, about eight miles from the company's headquarters.

  Calculate load voltage v2 and transformer voltage regulation

In a two-winding transformer N1 = 2000 and N2 = 500 and the supply voltage V1 = 1200 V. The transformer has winding resistances R1 = 2.0ohm and R2 = 0.125ohm , and leakage reactances X1 = 8.0 and X2 = 0.5ohm

  Find the length of the spring in the situation

Hooke's law describes a certain light spring of unstretched length 33.6 cm. When one end is attached to the top of a doorframe and a 7.31 kg object is hung from the other end, the length of the spring is 42.4 cm.

  Explain how does the carrier mobility depend on t

Which sample produces greater Hall voltage: long and narrow or short and wide Thickness (d) is same in both the cases. With little explanations please. 1) If the concentration of scattering centers increase in the semiconductor, would it increase o..

  Determine the algebraic sign of the voltage sources

where the assigned loop current leaves the voltage source. If current leaves the voltage source at its positive terminal, the voltage would be positive and if it leaves the voltage source at its negative terminal,the voltage would be negative.

  Vital information about system analysis and design

Important information about System Analysis and Design, Elmwood College Situation: The school is considering a new system that will speed up the registration process.

  Find the volume of a fcc primitive unit cell

For a face centered cubic, the volume of a conventional unit cell is a^3 Find the volume of a fcc primitive unit cell with three basis vectors: (0,0,0 --> a/2,0,a/2) and (0,0,0 --> a/2,a/2,0), and (0,0,0 --> 0,a/2,a/2)

  Calculate the power dissipated in the device

An InP TED is 0.5 pm long with a cross sectional area of 10" cm2 and is operated in the transit-time mode.(a) Find the minimum electron density no required for transit-time mode.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd