Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Gaussian White Noise with Power Spectral Density Sn(f) = 10 mu W/Hz is applied to a linear system with impulse response h(t) = exp(- |5t|)u(t)cos(2 phi 10t) Write the equation for the Power Spectral Density of the noise passed through the system. Sketch the Power Spectral Density of the noise passed through the system. Find the total power of the noise passed through the system.
A simple low-pass discrete-time filter is characterized by the following linear difference equation: y[n] = f y[n-1] +(1- f) x[n] , with 0 1 Draw and clearly label an adder-gain-delay diagram for the filter. using the same difference equation from a..
The contects of a six-bit register are initially 100101. The register is shifted four times to the right, with the serial input being 1101. What are the contents of the register after each shift
A signal is bandlimited to 20kHz. The band between 16 and 20 kHz is corrupted by noise such that the information is unrecoverable. Determine the analog lowpass filter maximum frequency to eliminate corrupted noise.
A room has four doors and four light switches (one by each door). Sketch a circuit that allows the four switches to control the light - each switch should be able to turn the light on if it is currently off, and off if it is currently on.
(a) The ideal delay system. y[n] = x[n-nd] (b) The accumulator system. y[n] = sum (xk) , k from -inf to n (c) Forward difference system. y[n] = x[n + 1]- x[n] (d) Backward difference system. y[n] = x[n]- x[n - 1]
A three-phase, wye-connected induction motor is supplied by a three-phase and foursin system with line-to-line voltage of 220V and the impedance of the motor is 6.3+j3.05Ohm per phase.
The voltage across a 0.2 H coil is given. What is the sinusoidal expression for the current?
A digital communication system transmits one of the three values -1,0,1. A channel adds noise to cause the decoder to sometimes make an error. The error rates are 12.5% if a -1 is transmitted, 75% if a 0 is transmitted, and 12.5% if a 1 is transmi..
Given a DSP system in which a sampling rate of 8000 Hertz is used and the antialiasing filter is a second order Butterworth low pass filter with a cutoff frequency of 3.2 KHz determine a. The percentage of aliasing level at cutoff frequency
Design a DC power supply that provides -95v +/- 5v to a 2 amp load (energy absorber). The input source is a 100 volt peak sinusoid, 60 Hz. You may use any circuit element we've studied. State the values of all circuit elements
Two amplifiers(CS) connected in cascade. The input voltage to the first stage has a source voltage Vsig and Rsig= 100KOhm. Rv=10KOhm AND IS CONNECTED TO THE DRAIN OF THE SECOND STAGE. BOTH TRANSISTORS HAVE Id=.25mA and Vov=.25V
The location of the zeroes in the spectrum suddenly changes to 5 kHz, 10 kHz, 15 kHz.... What parameter of the rectangular pulses has changed and what is its new value?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd