Find the torque required by each wheel

Assignment Help Mechanical Engineering
Reference no: EM131295757

The requirements needs to be followed and all calculations shown. If more information is needed let me know these are 3 to 4 bar linkages (see CAD drawing attached with dimensions)

need stress analysis?

angular velocity - low, middle, and high end?

circumference of rotation?

RPM of rotation - low, middle, and high end?

Maximum force required to move the parts forward?

there will be a wheel on the bottom ?

torque required by each wheel?

all parts are 1/4 inch aluminum ?

force required to move the walker forward?

required MOTOR RPM?

there are 2 sets of these to make as a walker

all calculations shown?

weight can be calculated by applying material to CAD drawing and adding the total multiply by 2 (2 sets of legs)?

for reference you can use "jansen linkage system" if needed.

sample stress analysis included but may not be correct


Attachment:- CAD drawing and Preliminary Analysis.zip

Reference no: EM131295757

Questions Cloud

What you would expect theoretically : The standard deviations of the distributions of b2 and b3 for the 10 million samples inFigure 3.5 are both 0.45. Verify that this is what you would expect theoretically, given that the correlation between X2 and X3 is 0.9962 and that S22 = 665 and S..
What implications can you see for managers in this story : What do you think of this? Do you agree that e-mail can be unproductive in the workplace?Were you surprised at the volume of e-mail an average employee receives daily? How much e-mail would you say you receive daily? Has your volume of e-mail incr..
How would you use other senses to compensate for the loss : Select one of the senses to discuss. In your own words, describe what your life would be like if that particular sense was not available to you. How would you use other senses to compensate for the loss?
Evaluate the effect of a minimum wage : From an economic standpoint, evaluate the effect of a minimum wage on the market for low-wage labor. Include the following:
Find the torque required by each wheel : The requirements needs to be followed and all calculations shown - need stress analysis? angular velocity - low, middle, and high end? circumference of rotation? RPM of rotation - low, middle, and high end? Maximum force required to move the parts fo..
How do in-store decisions affect market demand : How do in-store decisions affect market demand? How does advertising and brand design affect market demand? Forecast market demand by segment for each brand.
How did myspace differentiate itself from the competition : How did DeWolfe and Anderson recognize the opportunity for MySpace?What mistakes were made with Xdrive that ultimately made MySpace go more smoothly?How did MySpace differentiate itself from the competition?Evaluate the acquisition of MySpace as part..
What are your profits if you do not make the investment : What are your profits if you do not make the investment? What are your profits if you do make the investment? Instruction: Do not include the investment of $200 as part of your profit calculation.
Active monetary and fiscal policy : Select two subjects from the following list of topics and write a 1,050-word analysis: Active monetary and fiscal policy Increased government spending to fight recessions

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  If the vessel had a yield strength in compression in equal

the spherical bathyscaphe trieste that took 2 people to the bottom of challenger deep was 7 feet in diameter.if the

  Total extend time for drill feed is 30 seconds with

retrofit an existing clamp and drill circuit for maximum effeiciency. the cylinder that clamps the part into place is a

  What are the reaction forces of a pendulum at the pivot

what are the reaction forces of a pendulum at the pivot point at angles 0 45 and 90 from the horizontal. the pendulum

  Dpreciation value is 28 k based on a 329 depreciation the

assume the cost of a robotic system is 151. the salary and other costs of workers replaced is 27 the saving for using

  What is the machinability rating for the new material

If the machinability criterion were tool life for a cutting speed of 150 m/min, what is the machinability rating for the new material?

  Develop a 3 bit binary counter using d flip-flops

Compare and contrast the following three types of flip-flops: JK flip-flop, D flip-fl op, and T flip-flop. Indicate how the latter two flip-flops can be derived as special cases of a JK flip-flop. What is the practical use of the data "toggle" cap..

  The duct surface is maintained at 100 degrees c assuming

air flowing at 4x10-4kgs and 27 degrees c enters a sqaure duct that is 200mm on the side and 2m long. the duct surface

  What is the arithmetic mean or average

What is chance variation? What are the causes of it? How can it be altered?

  Determine a suitable set of dimensionless parameters

How will a measured pressure in the model be related to the corresponding prototype pressure? Assume the same air density in model and prototype. Based on the assumed variables, does the model wind speed have to be equal to the prototype wind spee..

  The tension t is increased in such a way that the string is

a 1-kg disk slides on a smooth horizontal table and is attached to a string that passes through a hole in the table.a

  Determine the hours of shading that occur each month

Prepare shadow maps for point P on the sun-path diagrams for 35°N and 40°N for the following three geometries shown in a, b, and c. Determine the hours of shading that occur each month.

  A gas-turbine power plant operates on a simple ideal

a gas-turbine power plant operates on a simple ideal brayton cycle with air as the working fluid. the air enters the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd