Find the specific flow exergy into and out of the steam

Assignment Help Civil Engineering
Reference no: EM131233675

Find the specific flow exergy into and out of the steam turbine in Example 7.1, assuming an ambient at 293 K. Use the exergy balance equation to find the reversible specific work. Does this calculation of specific work depend on T0?

Example 7.1

Steam enters a steam turbine at a pressure of 1 MPa, a temperature of 300?C, and a velocity of 50 m/s. The steam leaves the turbine at a pressure of 150 kPa and a velocity of 200 m/s. Determine the work per kilogram of steam flowing through the turbine, assuming the process to be reversible and adiabatic.

Reference no: EM131233675

Questions Cloud

Find all the fluxes of exergy in the refrigerator : The refrigerator in a kitchen shown in Fig. 5.7 receives electrical input power of 150 W to drive the system, and it rejects 400 W to the kitchen air. Find the rate of energy taken out of the cold space and the COP of the refrigerator.
State what you expect to be the results of the lab procedure : A hypothesis is an educated guess. Based on what you have learned and written about in the Introduction, state what you expect to be the results of the lab procedures.
As federal administrations change-requirements change : OSHA imposes obligations on the employer, but these obligations are not limitless. As federal administrations change, requirements change. Let's start by focusing on ergonomics. A major concern of OSHA throughout the 1990s was worker maladies such as..
Determine the quantities of materials required per cubic : Determine the quantities of materials required per cubic yard to create a concrete mix. - A maximum water-cement ratio of 0.63. Assume 5% air voids.
Find the specific flow exergy into and out of the steam : Find the specific flow exergy into and out of the steam turbine in Example 7.1, assuming an ambient at 293 K. Use the exergy balance equation to find the reversible specific work. Does this calculation of specific work depend on T0?
Determine total number of tons each of sand required : It is estimated that 8% of the sand and 6% of the gravel will be lost or not recovered in the stockpile at the job.-  Determine the total number of tons each of sand and gravel required for the project.
Write a short summary about concepts in the lab : This is an investigation of what is currently known about the question being asked. Use background information from credible references to write a short summary about concepts in the lab.
How will this project improve business supply chain : When deciding multiple projects, how will this project improve a business supply chain? This will potentially reduce the labor force by one third (about 100 people) and will potentially result in the sale or disposition of approximately $3 million wo..
Valuable for a non-mathematician : Discuss why it might be valuable for a non-mathematician, non-engineer to have an appreciation and/or a working understanding of higher level mathematics, even if the computations will not be part of their daily routine. Min of 100-150 words

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the compression index of the clay

A layer of normally consolidated clay has been filled with 2m of gravel at a unit weight of 17kN/m3 for a long period of time and the settlement of the clay layer monitored giving a total final settlement of 330mm.

  Determine the gas constant of the mixture

Determine the mole fractions of a gas mixture that consists of 75 percent CH4 and 25 percent CO2 by mass

  What is the friction force under each of the blocks when

A stepped shaft ACB having a solid circular cross sections with two different diameters is held against rotation at the ends. If the allowable shear stress in the shaft is 60MPa, what is the maximum torque (To)max that may be applied at section C?

  Determine the velocity of the collar at point b for values

To imagine the diagram, the collar at point A (unstretched) is on the same x-axis as the anchor @ C, while the collar point B (stretched) is located downwards-left to point A, forming a 30 degree angle with the y-axis (vertical). In other words, the ..

  When analyzing a truss using the method of sections to find

When analyzing a truss using the method of sections to find theforces in specific members. What is a good strategy to helpdecide where to make the cuts to separate the truss into separatesections?

  Calculate the molar mass of the biomolecule

For carbon tetrachloride, the boiling point constant is 5.03°C · kg/mol, and the boiling point of pure carbon tetrachloride is 76.50°C.

  Determine the force in each member

The truss shown consists of 9 members and is supported by a ball and socket at A, two short links at B, and one short link at G. Check that this truss is a simple truss, that it is completely constrained

  How could you reduce the required effort force

A 40 kg load is placed 3 m from a fulcrum. If an effort force is applied at a distance of 2 m, how much force is required to life the load to a horizontal balance? How could you reduce the required effort force? Are there any additional consideration..

  Determine the deflection of point c of the rigid member abc

KNowing that after being snugly fitted, the nut at C is tightened one full turn, determine (a) the tension in rod CD, (b) the deflection of point C of the rigid member ABC

  Primary consolidation settlement of the compressible

Determine total expected primary consolidation settlement of the compressible normally consolidated clay layer.  You must draw field consolidation line as part of your answer.

  Find the entropy generation using constant specific heats

A constant-pressure piston/cylinder is 2 lbm steel and it contains 1 lbm air at 540 R, 60 psia. The system is now heated to 2600 R by a 2800 R source, and the steel has the same temperature as the air. Find the entropy generation using constant sp..

  Determine its speed and acceleration at the instant

The motorcycle is traveling at 1 m/s when it is at A at the bottom of the ramp. If the speed is then increased at v=0.1 m/s^2, determine its speed and acceleration at the instant t=5s

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd