Find the required value of the filter capacitor

Assignment Help Electrical Engineering
Reference no: EM131194783

Write answer of given two questions.

1. A half-wave peak rectifier with a 1 k? load operates from a 120 V (rms) 60 Hz household supply through a 10-to-1 step down transformer. So 120 V (rms) appears at the primary side of the transformer. The output of the rectifier will be referred to as "Vout." Note that the primary and secondary of the transformer are in phase. Assume the ideal diode model.

a. Calculate the capacitance necessary to produce Vout so that its peak to peak ripple voltage (equation given in class) is 10% of the magnitude (or maximum value) of the voltage that appears across the transformer secondary.

b. Repeat part (a) if it is desired that the peak to peak ripple voltage of Vout is 5% of the magnitude of the voltage cross the transformer secondary. Note, the lower the ripple desired, the higher the capacitance necessary. Thus the capacitor is acting like a filter.

c. Calculate the DC load current.

2. It is required to use a full-wave peak bridge rectifier to design a DC power supply that provides an average DC output voltage of 15 V on which a maximum of +/- 1 V ripple is allowed. The rectifier feeds a load of 150 ?. The rectifier is fed from the line voltage (120 V rms, 60 Hz)
through a transformer. The diodes have a 0.7 V drop when conducting (at all currents).

a. Specify the rms voltage that must appear across the transformer secondary.

b. Find the required value of the filter capacitor.

Reference no: EM131194783

Questions Cloud

Summary of the keynesian model : ‘In circumstances of less than full employment, increased investment will generate the saving it requires'. Consider this statement as a summary of the Keynesian model. What assumptions does it embody?
Momentum business issue : Research Paper eight to twelve pages that depends on a momentum business issue that worries your work experience. It doesn't should be about your present place of employment, however ought to be unified with which you are exceptionally well known ..
How cultural identity impacts social responsibility : Explain how the theories align or do not align with your cultural identity. Include how cultural identity impacts social responsibility. Provide at least three references using proper APA format.
How have you personally been challenged to draw : How have you personally been challenged to draw from a diverse pool of individuals in your experience of "close" friendships? What are some of the barriers, if any?
Find the required value of the filter capacitor : Specify the rms voltage that must appear across the transformer secondary. - Find the required value of the filter capacitor.
Explaining the role of pension fund manager : FIN200 Assignment - FIN 200 Corporate Financial Management - "If the efficient-market hypothesis is true, the pension fund manager might as well select a portfolio with a pin." Explain why this is not the case.
Find the tensile stress in the bolts and compressive stress : The figure shows a steel pressure cylinder of diameter 4 in which uses six SAE grade 5 steel bolts having a grip of 12 in. These bolts have a proof strength (see Chap. 8) of 85 kpsi for this size of bolt. Suppose the bolts are tightened to 90 perc..
Different types of economies and economic conditions : Consider the different types of economies and economic conditions associated with them. Which type of economy is most beneficial for organizations and why?
Calculate the magnitude of fault current : If a fault from one phase to earth occurs on the far end of the feeder,  Calculate the magnitude of fault current. - Calculate line to neutral voltage at the generator terminal.

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Calculate the pressure of co2 in state 3

A piston-cylinder device contains carbon dioxide CO2 (molar mass = 46 g/mol) as shown in the figure. The cross-section area of the piston is 0.25 m2 and the initial cylinder height is 50 cm. CO2 is initially at 40 bar and 500 oC (state 1).

  What is the maximum conductivity can expect from oxide

For use in a liquid crystal display, you want an electrode that is transparent to all visible light. You decide to use a doped semiconducting oxide with a mobility of 10^(-2) m^2/V-s. What is the maximum conductivity you can expect from your oxid..

  Estimate the resistance of the human body using the figures

A stun gun or TASER is designed to put out a few seconds worth of electric pulses that impress a voltage of about 1200 V across the human body. This results in an average current of approximately 3 mA into a human body.

  Compute the available fading margin of antenna

The propagation law follows the free space up to a distance ofdbreak = 50 meters, and for larger distances the receive power is similar to(d/dbreak)-4.2. Transmit antenna gain is -7dB; the receive antenna gain is 9 dB. Compute the available fadi..

  Determine what is the total input current and power factor

A 120 kVA transformer is to be parallelled to a 60 kVA transformer. Each transformer has rated voltages of 10kV-120V at 60Hz. When supplying a 250A load at 0.85 PF, what is the total input current and power factor if the output terminal voltage is 12..

  Calculate the voltage drop across the load

A simple power system consists of a dc generator connected to a load center via a transmission line. The load power is 100kW. The transmission line is 50km copper wire of 3 cm in diameter. If the voltage at the generator terminals is 400V

  Question regarding the solar power plan

Discuss what is meant by the transient stability of a power system and what assumptions have you made for this study. Describe the procedure you need to carry out to determine the stability of the system.

  What precautions would take to prevent any equipment damage

An inductor and a capacitor are connected in series and connected to a variable frequency voltage source (e.g., a function generator). Explain what happens to the total circuit impedance and current as the source frequency is varied.

  Propose a sequence of experiments and data output

Problem: Using 3 pages, propose a sequence of experiments and data output considering the following questions:

  What is the largest peak value of impulse voltage

What is the largest peak value of impulse voltage that can be applied to a test object of 10nF - find the values of the wave front and wave tail resistances.

  Draw state diagram for fsm with no inputs and three outputs

Draw a state diagram for an FSM (Moore machine) with no inputs and three outputs x, y, and z, where xyz should always exhibit the following sequence: 000, 001, 010, 100, repeat. Make 000 as the initial state.

  Dynamic microphone changes sound into an electrical signal

Dynamic microphone changes sound into an electrical signal - Determine the Thevenin Equivalent circuit as seen from terminals A and B in the sketch

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd