Find the principal moments of inertia and the principal axes

Assignment Help Civil Engineering
Reference no: EM13310318

find the inertia tensor about the origin for a mass of uniform density=1,inside the part of the unit sphere where x>0,y>0,and find the principal moments of inertia and the principal axes.

Reference no: EM13310318

Questions Cloud

Explain the best combination of reactants for preparing : The best combination of reactants for preparing (CH3)2CHSH is a. (CH3)2CHBr + NaSH b. (CH3)2CHOH+CH3SH c. (CH3)2CHONa +CH2SH d. CH3CH2CH3 + NaSH
What pressure gradient along a streamline is required : What pressure gradient along a streamline, dp/ds, is required to accelerate water upwards in a pipe at 0.5 m/s^2  The incline is 1:10, i.e., 1 m upward for every 10 m horizontal
Explain the fescn2+ solution is an orange-brown colour : Why must we the wavelength bet set to 447nm when the FeSCN2+ solution is an orange-brown colour
What velocity will air exit under a small crack in the door : Laboratory clean rooms are often kept at a slightly higher pressure than ambient pressure in order to flush out particulates and keep dust from getting in. If the pressure in such a room is equivalent to 1 mm water greater than the surrounding roo..
Find the principal moments of inertia and the principal axes : find the inertia tensor about the origin for a mass of uniform density=1,inside the part of the unit sphere where x>0,y>0,and find the principal moments of inertia and the principal axes.
Give the steps for to build priority queue after deque : Both are given from a paper assignment both are Logic questions. I don't need ANY CODE AT ALL. Just the general steps you would use.
Determine the forces acting on member bh : The force exerted by the potatoes on the frame at one side of the chair is equivalent to horizontal and vertical forces of 24 N and 84 N, respectively, at E and a force of 28 N perpendicular to member BH at G.
How economics is used as a social science : Write a two-page essay in which you address the issues outlined above. Format your essay in a Word document using Times New Roman 12-point, one-inch margins and double spacing.
Compute magnitude and direction of his average acceleration : A football player carrying the ball runs straight ahead at the line of scrimmage and directly into a wall of defensive linemen. Find the magnitude and direction of his average acceleration

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the x-y and z components of the force exerted

Cable AC is 70 ft long, and the tension i nthe cable is 5250 lb. Determine the x, y, and z components of the force exerted by the cavle on the anchor C. Also, find the angles theta-x, theta-y, and theta-z defining the direction of the force.

  Design riveted end plated connection between beam and flange

Design a riveted end plated Connection between a beam ISHB-300 and the flange of the Column ISHB-200 to transfer a vertical factored shear of 125 kN and a factored hogging bending moment of 125kNm.Use Shop rivets of 20mm dia.

  Determine the strain components strainx and strainy

Determine the strain components strainx, Strainy, and gammaxy, then sketch the deformed shape in the xy orientation, paying particular attention to the sign of the shear deformation.

  Estimate average shear stress on pipe and friction factor

Water is flowing in a horizontal 200-mm diameter pipe at a rate of 0.05 m^3/s, and the pressures at sections 80 m apart are equal to 500 kPa at the upstream section and 400 kPa at the downstream section.

  Determine the service rate for six vehicles per minute

Vehicles begin to arrive at a toll booth at eight vehicles per minute from 9 A.M. to 10 A.M. The booth opens at 9:10 A.M. and services at a rate of ten vehicles per minute until 9:40 A.M. From 9:40 A.M. until 10 A.M.

  How to formulate a set of constraints that will enforce

Given the binary variables x1,x2,x3,x4 and x5, formulate a set of constraints that will enforce x3,x4, and x5 to equal one if x1=1 and x2=0.

  What is the draft h of the barge when floating in sea water

A barge has the trapeziodal shape and is 22 m long into the paper. If the total weight of barge and cargo is 350 tons, what is the draft H of the barge when floating in sea water

  How much of the borrow material is required to fill the site

The material is brought from a borrow site that has yt=19.5 kn/M63 with w=16.5% and Gs=2.70 How much of the borrow material (in cubic meters) is required to fill the site  How heavy is it

  Determine the total number of unit cells in the foil

aluminum foil used to package food is approximately 0.001 inch thick. assume that all of the unit cells of the aluminum are arranged so that a is perpendicular to the foil surface.

  Estimate the land area in acres that must be purchased

The city has a stable population of 235,000 residents and the design criteria for the new landfill are as follows: MSW generation rate = 4.0 lb/(person-day); density of the compacted MSW in the landfill is 775 lb/yd3

  Determine the stoichiometric oxygen requirement for fuel

Determine the Stoichiometric oxygen requirement (pounds of oxygen per pound of fuel) for a fuel containing by weight 50% n-octane,25% 1-heptene and 25% methanol.

  Find si value of absolute pressure corresponding to vaccum

What is the SI value of absolute pressure corresponding to a vacuum pressure of -10 inches of water. Assume the location is Moscow, Idaho. What is the SI value of gage pressure corresponding to a pressure 14 psia. Assume the location is Denver, Colo..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd