Find the instantaneous and rms value current supplied

Assignment Help Electrical Engineering
Reference no: EM13261685

A single-phase load is supplied with a sinusoidal voltage
v(t) = 200 cos(377t)
The resulting instantaneous power is
p(t) = 800 + 1000 cos(754t ¡ 36:87±)
(a) Find the complex power supplied to the load.
(b) Find the instantaneous current i(t) and the rms value of the current supplied to the load.

Reference no: EM13261685

Questions Cloud

Explain a living organism has an activity : Carbon-14 has a half-life of 5730 yrs. A living organism has an activity of 15.2 counts per minute (cpm) per gram of carbon. If a bone is determined to have an activity of 3.80 cpm per gram of carbon, how old is the bone
Write a function to have a user enter some number of integer : The integer array and the size of the array are passed into the function through parameters. Do not worry about includes. This is only a function, so there is no main routine. The function should fill the array with valid inputs.
Discuss different theories of psychology : What knowledge did you have about it? What were your feelings about it? What about the topic was significant enough to you that you had thought about it before the semester started?
Explain what is the particle : Bombardment of cobalt-59 with a neutron produces a manganese-56 atom and another particle. What is this particle
Find the instantaneous and rms value current supplied : A single-phase load is supplied with a sinusoidal voltage v(t) = 200 cos(377t) The resulting instantaneous power isp(t) = 800 + 1000 cos(754t ¡ 36:87±)  (a) Find the complex power supplied to the load.
What is the maximum speed of the glider : An air-track glider attached to a spring oscillates between the 16.31 cm mark and the 51.41 cm mark on the track. What is the maximum speed of the glider
How to use the tabulated half-cell potentials : Use the tabulated half-cell potentials below to calculate the equilibrium constant (K) for the following balanced redox reaction at 25°C.
Determine the maximum and minimum values of magnitude : Determine the expression for the frequency response H(Omega) of a causal IIR LTI discrete-time system characterized by the input-output relation. where |a|
What is the phase angle of the circuit : A 60 ohm resistor is connected in series with a 30x10^-6 capacitor and a generator having a maximum voltage of 120 volts, what is the phase angle of the circuit

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Write the analytical expression for the waveforms

What would be the initial value of v c (t) when switch is closed and determine the time constants in both cases (switch is open, switch is closed).

  Explain a square wave signal with voltage levels

A square wave signal with voltage levels 0 volts and 2.0 volt at a frequency of 1.00 MHz is multiplied by a sine wave at a frequency of 5.0 MHz

  Explain the maximum symbol rate that the twisted pair

What is the maximum symbol rate that the twisted pair line can carry without ISI? 256-QAM modulation is used on the link. How many bits are conveyed by each symbol?

  Find the ratio of the effective density of states

n the conduction band of a semiconductor, it has a lower valley at the center of the Bril- louin zone, and six upper valleys at the zone boundary along [100]. If the effective mass for the lower valley is 0.1m0 and that for the upper valleys

  Calculate the maximum value of r2 to compensate

A series type Ohmmeter uses a 50 ohm, 1mA PMMC the internal battery voltage is 3V the desired scale marking for half scale deflection is 2000 ohm. Calculate:- - Value of R1 & R2

  Determine the standing wave pattern for the voltage

Determine the standing wave pattern for the voltage in the line. Express the result in real insantaneous form and simplify

  Calculate motor speed in revolutions per minute

4.What is the fundamental benefit of PLC controls over manual controls 5.Describe the differences between the two methods of scanning during PLC logic solving. Which method holds the advantage over the other

  Find beta cutoff frequency of bjt and unity gain frequency

A BJT has beta =100,mod Aie=10 at 10 MHz and it is operating at a collector current of 5 mA.If transition capacitance =10pf 1) calculate beta cutoff frequency of BJT,unity gain frequency and diffusion capacitance

  How the ct-vt and meters are connected into the load circuit

Draw a circuit diagram to show how the CT, VT and meters are connected into the load circuit. Neglecting instrument and transformer errors, calculate the load kVA and power factor if the voltmeter, ammeter and wattmeter indicate values of 200 V, 2..

  Explain how the ideal op amp is a high-gain amplifier

The current through a branch in a linear network is 2 A when the input source is 10 V. If the voltage is reduced to 1 V and the polarity is reversed, the current through the branch is a. - 2 A b. - 0.2 A c. 0.2 A

  Calculate and plot the waveforms for va an ea

The motor driven by a switch-mode dc-dc converter, which has a bus voltage of 200V. The switching frequency fs = 25 kHz. Calculate and plot the waveforms for va(t), ea(t), ia(t), and id(t) under the following conditions

  What must the magnitude of the charge in micro coulombs

The space between the plates is then filled with a dielectric material, with dielectric constant k = 6.55. What must the magnitude of the charge in micro coulombs on each capacitor plate now be, to produce the same potential difference between the..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd