Find the input impedance at a distance from the load

Assignment Help Electrical Engineering
Reference no: EM13267842

Consider a transmission line with Ro=50-ohm connected to an 850 MHz, 50ohm generator and a load ZL=75 + j10 ?. Find the input impedance at a distance of 0.2m from the load using a Smith Chart. Include the Smith Chart used to solve this problem.

Reference no: EM13267842

Questions Cloud

Explain the heat of vaporization of isopropyl alcohol : Patients with a high body temperature are often given "alcohol baths." The heat of vaporization of isopropyl alcohol (rubbing alcohol) is 159 cal/g. How much heat is removed from the skin by the evaporation of 190g about 1/2 cup) of isopropyl alco..
What final payment will the bank require : If the interest rate on the loan is 7%, what final payment will the bank require you to make so that it is indifferent to the two forms of payment?
Explain the growth of the white house staff : How do you explain the growth of the White House staff during the 20th Century and is this growth a positive or negative development for the presidency? Why?
Design an open-circuited shunt stub matching network : Design an open-circuited, shunt stub matching network to match a 125 + j20 ohm load to a 700 MHz, 50ohm generator. Show the lengths of your transmission lines in fractions of a wavelength.
Find the input impedance at a distance from the load : Consider a transmission line with Ro=50-ohm connected to an 850 MHz, 50ohm generator and a load ZL=75 + j10 ohm. Find the input impedance at a distance of 0.2m from the load using a Smith Chart.
Calculate the net annual benefit of the proposed : A permanent working capital investment of $60,000 is expected to produce an annual after-tax cash inflow of $18,000 for many years and has a cost of capital of 12%. Calculate the net annual benefit of the proposed permanent working capital investm..
What is the estimated annual change : What is the estimated annual change to Year 1-n cash flow due to depreciation from a capital budgeting investment costing $100,000 with a useful life of 12 years and a salvage value of $28,000? Assume a 34% tax rate and straight-line depreciation.
What is the rms value of the secondary transformer voltage : Design a full wave (60Hz) rectifier circuit with the capacitor filter that produces 5V 10A DC at the output with the ripple voltage of less than 5%. (Assume Von = 1 for the diodes and do not forget to draw your circuit and a time diagram of the vo..
What is the speed of the muon : Consider the motion of a muon as it moves through the Earth's atmosphere. After a time ? = 2.20 multiply.gif 10-6 s, What is the speed of the muon

Reviews

Write a Review

Electrical Engineering Questions & Answers

  How many units must we sell to recover increased design cost

a cost to produce, P, of $4.00. If we were able to reduce this to $3.55 through greater attention in the design, and if the cost to improve the design (in NRE) is $35,000, how many units must we sell to recover the increased design cost.

  Determine the maximum and minimum values of magnitude

Determine the expression for the frequency response H(Omega) of a causal IIR LTI discrete-time system characterized by the input-output relation. where |a|

  Design a power supply using a center-tapped transformer

Design a power supply using a 24V, center-tapped transformer to supply 12V at 500mA, -12V at 100mA and 5V at 250mA. What is the minimum current rating of the transformer

  What is turbine type and estimate flow rate of each turbine

Turbines at the Conowingo plant on the Susquehanna River each develop 54,000 hp at 82 RPM under a head of 89 feet. What is the turbine type Estimate flow rate of each turbine.

  Indicate which actions are time-driven nd which event-driven

Discuss the sequence of actions that occur in the operation of the control system for a traffic light, that includes sensors in the roadbed. Indicate which actions are time-driven and which actions are event-driven

  What sampling rate should use for aliasing frequencies

use a third-order low pass filter with a -3dB frequency of 10 Hz to filter your signal. What sampling rate should you use to make sure any potentially aliasing frequencies are attenuated by at least -40 dB for a. A butterworth filter

  What value of field current will result in a unity pf

A synchronous motor is drawing 90 amps from 240V, 3 phase line at 0.8 pf leading with field current adjusted to 1.2 amps. The synchronous machine Xd is 1.3 ohms. Find a). The power angle delta

  What is the shortest possible line length

what is the shortest possible line length that would exhibit the desired reactance at its input?

  Desing a mod-16 asynchrous ripple up counter

Desing a mod-16 asynchrous ripple up counter by using j-k flip-flops. You need to design a j-k flip flop first and use it as the component in mod-16 up counter design. Show both j-k flip-flop design implementation results .

  Why sinusoidal wave is chosen for ac fundamentals

why sinusoidal wave is chosen for AC fundamentals rather than a simple curve such as square or triangular wave?

  How many years ago was the desired ration of recreation land

How many years ago was the desired ration of recreation land per 1,000 population exceeded if no more land was acquired and the population continued to grow at the indicated rate

  Write the ybus matrix

Identify the bus types and the unknown variables of the power flow problem. Write the complete set of equations needed to solve the load flow problem.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd