Find the final speed of the puck b and a after the collision

Assignment Help Electrical Engineering
Reference no: EM13278290

Hockey puck B rests on a smooth ice surface and is struck by a second puck A, which has the same mass. Puck A is initially traveling at 14.6 and is deflected 28.0 from its initial direction. Assume that the collision is perfectly elastic.

a)Find the final speed of the puck B after the collision.
b)Find the final speed of the puck A after the collision.
c)Find the direction of B's velocity after the collision.

Reference no: EM13278290

Questions Cloud

Find the maximum speed in the vertical plane : A circular disk having a radius of 4 ft and weighing 40lb has a small weight of 20lb attached to it at a distance of 2ft from its center. If the disk is in the vertical plane and set in rotation about an axis through its center so that its minimum..
Explain ammonia reduces copper oxide to the free metal : At high temperature, ammonia reduces copper(II) oxide to the free metal: Step 1: 2NH3(g) + 6CuO(s) => N2(g) + 3Cu2O(s) + 3H2O(g)
How much energy is stored in the flywheel at the end of 20s : A torque of 10 N.m is applied to a uniform disk shaped flywheel. The flywheel has a mass of 20kg and a radius of 0.5m. At t=0, the flywheel is at rest. How much energy is stored in the flywheel at the end of 20 sec
Explain the equilibrium partial pressure of nh3 increases : or each of the following cases, briefly explain whether the action causes net reaction from left to right, right to left, or no net reaction. Also, state whether the equilibrium partial pressure of NH3 increases, decreases or stays the same. (a) i..
Find the final speed of the puck b and a after the collision : Hockey puck B rests on a smooth ice surface and is struck by a second puck A, which has the same mass. Puck A is initially traveling at 14.6 and is deflected 28.0 from its initial direction. Assume that the collision is perfectly elastic.
Explain the magnitude of the partial charges in hbr : Determine the magnitude of the partial charges in HBr given that the bond length is 1.41 angstroms and the dipole moment is 0.82 debye.
Explain the formation reaction of h2so4 : Which one of the following reactions occurring at 25 ?°C is the formation reaction of H2SO4(l) a. H2(g) + S(s) + 2O2(g) => H2SO4(l) b. H2SO4(l) => H2(g) + S(s) + 2O2(g) c. H2(g) + S(g) + 2O2(g) => H2SO4(l) d. H2SO4(l) => 2H(g) + S(s) + 4O(g) e. 2H..
Explain how copper sulfide is formed : When copper is heated with an excess of sulfur, copper(I) sulfide is formed. In a given experiment, 2.33 g of copper was heated with excess sulfur to yield 1.76 g of copper(I) sulfide. What is the percent yield
What was the time of death : Assume that the temperature of the body at the time of death was 98.6 fahrenheit and that is has cooled in accourd with Newton's law. What was the time of death ?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the probability that cars will experience catastrope

An automobile manufacturer is concerned about a fault in thebraking mechanism of a particular model. The fault can, onrare occasions, cause a catastrophe at high speed. The distrubution of the number of cars per year that will experience

  Give subroutine to perform lower-to-upper case conversion

Write and test a program for the EASy68k to input a string from the keyboard, convert all letters to uppercase and echo (output) the new string to the screen. Use a subroutine to perform the lower-to-upper case conversion.

  Determine the length of the transmission line

A transmission line of char. Impedance 100ohm is used to match a 50ohm section to a 200 ohm section. if the matching is to be done both at 429MHz and 1GHz the length of the transmission line can be approx?.

  Depiction impedance diagrams

Determine the system fault kVA and the fault currents at the 415 V and 110 V busbars for short circuit faults on the transformer input or output terminals. Work in p.u. values of impedances.

  What condition is relation in na-nd nd no good approximation

Compensation occurs when a semiconductor is doped with both donor and acceptor dopants. Using the fact that n0p0=ni^2 (mass action law) and p0+Nd=n0+Na (charge neutrality assuming all dopants are ionized)

  Obtain an corresponding iir digital high passs filter

The normalized lowpass filter with a cutoff frequency of 1 rad/sec is given as Hp(s) 1/s+1 a. Use Hp(s) and the BLT to obtain an corresponding IIR digital high passs filter with a cutoff of 30 Hz, assuming a sampling rate of 200 hz,

  Find the phase relation between the total voltage nd current

Then find the phase relation between the total voltage and current; is it leading or lagging when the frequency is below resonance and above resonance; what is the nature of the circuit in those two regions(capacitive or inductive).

  How long will it take to transmit the three ascii code

how long will it take to transmit the three ASCII code to characters $14 in 8 bit parallel if the clock frequency is 8 MHz? Repeat for $78.18 at 4.17 MHz

  Find what is steady-state stability and transient stability

1) During a transient fault and a permanent fault on the transmission line of a power network, mention the sequence of a line circuit breaker's operation. 2) During a network fault, the voltage and active power of a synchronous generator drops

  Determine the overall gain when the amplifier is connected

The first stage is a transconductance amplifier with an input resistance of 2k ohms, an output resistance of 100k and a gm=0.002A/V. The second stage is a voltage amplifier with an input resistance of 5k, an output resistance of 18 ohms and a volt..

  What is the time needed to complete the faster process

A p-type wafer has a diffused Phosphorous n-type junction with a junction depth of 0.15µm. a) If the wafer (no pre-existing oxide) is to be oxidized at 1000 C for two hours to form a ‘dense.

  Find what is the standing wave ratio on the line

A 75 ohms lossless air transmission line at 3 GHz is terminated in a load of (300-j400) (a) What is the load reflection coecient (b) Determine the impedance at 2.5 cm, 5.0 cm, 7.5 cm and 10 cm from the load.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd