Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.Find the critical depth for a flow of 6 m3/s in a triangular channel; one side of the channel is vertical and the other side makes an angle of 30° with the horizontal.
2.The rate of flow through a trapezoidal open channel is 20 m^3/s and the mean velocity of flow is 1m/s . the side slope is 1:1 and the bed slope is 1 in 5000. Assume Chezy's constant C as 60, find the bottom width and the depth of water channel.
3.The rate of flow through a trapezoidal open channel is 20 m^3/s and the mean velocity of flow is1 m/s . the side slope is 1:1 and the bed slope is 1 in 5000. Assume Chezy's constant C as 60, find the bottom width and the depth of water channel.
A micro-channel of diameter 0.5 mm and length 750 mm is connected to a plenum. A fan produces a negative gage pressure of -1.5 inch H2O in the plenum and draws air at 20oC into the micro- channel.
If, on 8/1/2019, 3-year municipal bonds with an AA- rating and a coupon rate of 6.50% (payable semiannually) are selling for $100.00, what would be the fair market value of the 300 Whittier bonds (not including the 8/1/2019 coupon payment)
Calculate the compression resistance of 200 UC 59.5 column which is 3.6 m high (between lateral supports). Both ends of the stanchion are held effectively in position but only one is also restrained in direction. Use grade 43 steel
Determine the maximum external pull, in each of the four gears, for a tractor with 23-hp, and a max speed of 3.6 mph in 1st gear and a efficiency of 92%. When it is operated over a haul road whose slope is +2.53%.
For a rubber component that, in its final form is to be vulcanized, should vulcanization be carried out prior or subsequent to the forming operation? Why?
Consider a Carnot heat-engine cycle executed in a steady-flow system using steam as the working fluid. The cycle has a thermal efficiency of 35%, and steam changes from saturated vapor at 300 C during the heat addition process. If the mass flow rate ..
Explain CBR method of pavement design with one example.
Air (an ideal gas) enters an adiabatic nozzle at 3 bar and 38 C and exits at 1 bar and -0.78 C. The process is steady. If the velocity at the inlet is 1 m/s, determine the exit velocity and the ratio of the exit area to the inlet area.
Compute and plot (or clearly sketch) the vertical effective stress distribution up to a depth of 34 ft of silt deposit before the lowering of the water table.
Water is pumped up 20 feet from one large, open tank to another large, open tank as shown in the figure below. The pipe connecting the 2 tanks has a total length of 200 feet and a diameter of 6 inches.
An ogee spillway of a gravity dam is to be modeled using water. The spillway section is 40 feet high, its crest length is 60 feet and the maximum discharge is 3,000 CFS when the head on the crest of the spillway is 5 feet. Using a model scale of 1:10..
atmospheric air at 1.01 bar 30 c and 60 percent relative humidity flows over a set of cooling coils at an inlet flow rate of 1500 m^3/min the liquid which condeness is removed from the system at 17 c
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd