Find specific mechanical energy and power available in wind

Assignment Help Civil Engineering
Reference no: EM13319061

Consider a wind turbine at elevation of 7000 ft. The air pressure is taken to be 80kPa and the mean annual temperature is 2 degrees Celsius. What are the specific mechanical energy and power available in thw wind that a wind turbine with 60m diameter blades might be able to harvest assuming that the mean wind speed is 10 m/s?

Reference no: EM13319061

Questions Cloud

Calculate the viscosity of the lubricating oil : A 4 in. in diameter shaft moves through a well-oiled sleeve that is 12 in. long. The force required to move the shaft is 25 lbf, and the shaft velocity is 5 in./s.
How far does the car skid before stopping : A 1500kg car slams the brakes on, its initial speed is 32m/s, How far does the car skid before stopping
Find the angle of refraction for red light : The index of refraction for a diamond for red light of wavelength 654 nm is 2.35, Find the angle of refraction for red light
A straight line indicating the law of increasing opportunity : Which of the following correctly characterizes the shape of a production-possibilities curve? A) A straight line indicating the law of increasing opportunity costs applies
Find specific mechanical energy and power available in wind : The air pressure is taken to be 80kPa and the mean annual temperature is 2 degrees Celsius. What are the specific mechanical energy and power available in thw wind that a wind turbine with 60m diameter blades might be able to harvest
How will this information change your answers in a b and c : Congratulations again. You've just been appointed economic advisor to Examland. The mpe is .6; autonomous investment is $1,000; autonomous government spending is $8,000;
Determine expressions for attractive and repulsive energies : Consider some hypothetical X+ - Y - ion pair for which the equilibrium interionic spacing and bonding energy values are 0.38 nm and - 6.38 eV respectively. If it is known that n in the equation has a value of 10
How to calculate the vitamin b1 content of the pork : The following data was recorded. Solution: Relative Fluorescence A (standard oxidized) 62.4 B (standard, blank) 7.0 C (sample, oxidized) 52.0 D( sample, blank) 8.0 Calculate the vitamin B1 content of the pork in terms of micrograms per gram.
The enconomy experienced a servere recession : Some politicians have suggested that the U.S. enact a constitutional amendment requiring that the federal government balance its budget annually. Explain why such an amendment

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine which equation is valid in any system units

According to information found in an old hydraulies book, the energy loss per unit weight of fluid flowing through a nozzle connected to a hose can be estimated by the formula h=(0.04 to 0.09)(D/d)^4*V^2/2*g

  Determine the magnitude of the moment produced

The pipe assembly is secured on the wall by the two brackets. If the flower pot has a weight of 50lb, determine the magnitude of the moment produced about the x, y and z axes.

  Determine the minimum do concentration in the stream

A municipal WWTP discharges 22.5 MGD of secondary effluent containing 45 mg/L of ultimate BOD at 26.7 C with 1.3 mg/L of dissovled oxygen. The stream flow is 237 ft^3/s at an average velocity of 2.1 ft/s and an average depth of 7ft.

  Determine what is the adiabatic efficiency of the turbine

At the inlet the steam is at 1 MPa and 320 C, and leaves the turbine at 20 kPa. The work output of the turbine is measured to be 600 kJ/kg (of steam passing through the turbine).

  Explain how to estimate the diameter of the small pipe

Fluid flows steadily, at a volume rate Q, through a large pipe and then divides into two small pipes, the larger of which has an inside diameter of 25 mm and carries three times the flow of the smaller pipe.

  Determine mass flowrate through boiler needed to produce

Determine the mass flowrate through boiler needed to produce 5000KW of power.

  Find the correction for the calibration of the measuring tap

Find the correction for the calibration of the measuring tape using its formula. During the calibration of the measuring tape on comparator of 100.000m the length of the tape turned out to be of 99.993m

  Determine the initial length of the rod measured

To determine the original length of a slender rod given the normal strain and deformation experienced by the rod due to an applied axial load. rod AB is subjected to the loading of two blocks, each of weight W

  Find the magnitude and location of the resultant force

You are to assume that seawater at 77oF will be used in the tank and the curved portion forms a quarter of a circle. The tank is open to the atmosphere. The overall height, h2, is 20ft deep. The radius of the curve, R, is 5ft. The width of the..

  Determine the components fa and fb along the oblique

Determine the components Fa and Fb of the 4.2 kN force along the oblique axes a and b. Determine the projections Pa and Pb of F onto the a- and b-axes.

  Determine what is the mass of the object necessary

An object is held in the air 30m above ground and released. Assume the drag force due to air resistance is given by Fd = 1.0Vy. What is the mass of the object necessary so that it reaches ground in 3s

  Calculate the base width of channel of side slopes

A trapezoidal canal of side slopes 1V : 2H, and having n = 0:017 is to carry a uniform flow of 37 m^3/s on a slope of 0.0005 at a depth of 1.5 m. Calculate the base width of channel

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd