Expresses the relationship for the change in entropy in a

Assignment Help Civil Engineering
Reference no: EM13549267

1.Which of the following expresses the relationship for the change in entropy in a reversible process between two end states, and then the change in entropy in an irreversible process between the same two end states?

A) (S2-S1) irreversible = (S2-S1) reversible

B) (S2-S1) irreversible > (S2-S1) reversible

C) (S2-S1) irreversible < (S2-S1) reversible

D) None of the above

2.Steam at 10 MPA, 600 C, enters a well insulated turbine operating at steady state and exits at 0.1 bar and a quality of 92%. The volumetric flow rate at the inlet is 0.36 m^3/s. Assuming the kinetic and potential energy effects to be negligible, determine

A) the mass flow rate in kg/s

B) the temperature at the exit of the turbine, in C

C) the power developed by the turbine in kW

D) the isentropic turbine efficiency

E) the entropy at the exit of the turbine, in kJ/kg K

F) the rate of entropy production within the turbine, in kW/K

Reference no: EM13549267

Questions Cloud

Determine the system curve for the pump system : Water is pumped from the tank 1 to tank 2 as shown below. The suction side pipe is nominal 4, schedule 40, 24 ft long, f = 0.018, and the discharge pipe is nominal 3 ½ , schedule 40, f = 0.019, and is 400 ft long
Properties must be the same throughout the system : The interaction that occurs between a system and its surroundings as the system executes a process, which is the result of the system being at a temperature different from that of the surroundings.
Determine the vertical deflection and the slope at the end : Determine the vertical deflection and the slope at the end of A of the bracket. Assume that the bracket is fixed supported at its base, and neglect the axial deformation of segment AB. EI is constant.
A 100 lb door has a weight of 100 lbs and a center : A 100 lb door has a weight of 100 lbs and a center of gravity at point g. determine the resultant force at points A and B. Point B resists forces in the X and Y directions. Point A resists forces in the X, Y and Z directions. The bottom horizontal ed..
Expresses the relationship for the change in entropy in a : Steam at 10 MPA, 600 C, enters a well insulated turbine operating at steady state and exits at 0.1 bar and a quality of 92%. The volumetric flow rate at the inlet is 0.36 m^3/s. Assuming the kinetic and potential energy effects to be negligible, dete..
Discuss the role that you believe your surety would play in : The New Jersey Surety Association, in various documented publications discusses the Surety’s relationship with their clients, the best ways to better know your Surety and a brief overview of why the Construction Business can fail.
Each of the three partners realizes that in order for the : Hardly Able Contracting Co., Inc., Contractors & Engineers, has been in business for twenty five years and has been progressively expanding since the firm’s inception
Helium gas is compressed is entropically from 1 bar and 25 c : Helium gas is compressed isentropically from 1 bar and 25 C to a pressure of 10 bar. The temperature of Helium after the compression is A) 25 C B) 63 C C) 250 C D) 384 C E) 476 C
Find the probability that in 30 years : An insurance sales representative sells policies to 5 men, all of identical age and in good health. According to the actuarial tables, the probability that a man of this particular age will be alive 30 years hence is 2/3. Find the probability that in..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine height and the velocity of the water downstream

The centres of the piers in a bridge are 8.0m apart. The piers are each 0.8m wide. Water flow under the bridge with an upstream depth and velocity of 4.0m and 4.0m/s respectively. The pier has a drag coefficient Cd = 1.5.

  What considerations would made with regards to cement type

You are a construction engineer working on a large concrete foundation project, involving the placement of over 500,000 c.y of concrete. The construction site is adjacent to a salt-water source (bay) & it is decided to set up a concrete batch plan..

  Provide zero-air voids curve for the soil on the same plot

a) Density plot, locating γd(max) and ω opt on the plot b) Zero-air voids curve for the soil on the same plotc) Curve representing S = 70%

  Explain traction and total resistance

Traction and Total Resistance, Would you please help me with the following question: A 90 tonne rear dump truck travels on an 8% grade loose gravel road.

  What will the ammonia concentration be 10 miles downstream

The concentration of ammonia is 6 mg/L at one point in the river. If the first – order decay coefficient for the conversion of ammonia to nitrate is 0.05 day-1, what will the ammonia concentration be 10 miles downstream.

  Determine the mass of b to maximize the impulse applied

to apply shock loading to an artillery shell, a 20kg pendulum A is released from a know height and strikes impactor B at a known velocity v (theta). impactor B then strikes the 1 kg artillery shell C.

  Determine if intersection provides appropriate changes

Your job as a Highway Patrol Officer is to place a sign to ‘Slow Down' on the freeway prior to a major construction site. The posted freeway speed is 65 mph and a speed of 35 mph is required through the construction site.

  What is magnitude of total external force on the helicopter

During a test flight in which a 9000-kg helicopter starts from rest at t = 0, the acceleration of its center of mass from t =0 to t =10 s is a=(0.6t)i+ (1.8 0.36t)j m/s2.

  Determine the oxygen concentration below the dam

A singly reinforced concrete beam has b=24in, d=12in and it is reinforced with 6#9 bars. If f'c=4ksi and fy=60ksi, determine the beam capacity, Mu = fMn.

  What would height be after it was consolidated into packing

A 1m thick layer of this soil is packed so that it is as loose as possible (void ratio, e_max ~= 0.9), and then it was vibrated until it was as dense as possible (void ratio, e_min ~= 0.35).

  Determine the distance the engine is hoisted

The 3.5-Mg engine is suspended from a spreader beam having a negligible mass and is hoisted by a crane which exerts a force of 40 kN on the hoisting cable. Determine the distance the engine is hoisted in 2.4 s, starting from rest.

  Determine the maximum flexural stress in the rod

A steel rod of 1/8 inch diameter is bent into a loop 10 feet in diameter. Determine the maximum flexural stress in the rod.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd