Express the logic governing the two devices

Assignment Help Mechanical Engineering
Reference no: EM131199665

A one-way road meets a two-way road, as shown in Figure P8.25. The vehicles on the one-way road are allowed to make right turns and left turns only (i.e., it is a dead end). There are sensors to detect vehicles at positions A, B, and C, which generate high signals (logic-1) when vehicles are present and low signals (logic-0) when vehicles are not present. Logic hardware devices are to be developed to operate the right-turn signal (with active-high output R) and the left-turn signal (with active-high output L) in the one-way road. Inputs to these devices are the logic signals denoted by A, B, and C, as generated by the vehicle-detection sensors.

The logic governing the operation of the two signals is as follows: The right-turn signal is on when there are no vehicles at A and there are vehicles at C. The right-turn signal is on as well, when there are no vehicles at A, B, and C. The left-turn signal is on when there are no vehicles at A and B and there are vehicles at C.

(a) Express the logic governing the two devices

(b) Using a K-map, minimize the logic, if possible (c) Give circuits for implementing the two devices using NOR gates and NOT gates only

Figure P8.25

2465_3876aedd-4159-492e-99d8-f2f9b42a75b9.png

Reference no: EM131199665

Questions Cloud

Calculate translational contributions to internal energy : Calculate the translational, rotational, vibrational (calculate excluding and including the zero point energy term), and electronic contributions to the internal energy (U) for gaseous ammonia at 25 ºC and 1 bar
Review quality and risk management tools and strategies : Discuss the role of quality and risk management to health care outcomes, including challenges in collecting and analyzing quantitative data in the health care environment, components of quality, and the fundamentals of outcome measurement. Review ..
Important to a business organization : Kindly help me in this, How is reputation important to a business organization?
Indigenous populations of north america : You will now write an introduction stating your position by answering whether you think the impact European contact had on the indigenous populations of North America should be addressed as a historical question or a moral question.
Express the logic governing the two devices : The logic governing the operation of the two signals is as follows: The right-turn signal is on when there are no vehicles at A and there are vehicles at C. The right-turn signal is on as well, when there are no vehicles at A, B, and C. The left-t..
Endowment points and indifference curves : a. Draw their endowment points and indifference curves in the same graph. b. If they live on separate islands, and cannot trade with each other, can you explain what the equilibrium price would be on each island? (Draw the budget set through the e..
How modern liberalism varies from classical liberalism : In an effort to better understand these various meanings, we need to explore the variations within liberalism itself. So who would like to explain how modern liberalism varies from classical liberalism? In addition, in what ways is classical libera..
The perception of color : The perception of color. How is it that two or more people can look at an object and not agree it is the same color? What does it mean to be color blind? What does fall foliage do the brain and how does it affect the way we feel?
Give the circuit for an rs flip-flop using nor gates only : Give the circuit for an RS flip-flop using NOR gates only. Extend this to an asynchronous latch circuit, using NOR gates and NOT gates.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the normal stress on a plane inclined at an angle

the principal stresses at a given point are 10 mpa a2 -100 mpa. sketch mohrs circle for this state of stress and

  Balanced-cross-flow compact heat exchanger

A balanced-cross-flow compact heat exchanger is required for an air heating system that processes 0.5 kg/s air. The inlet temperature for the hot water is 295 K, and the cold air enters at 270 K to be heated to 287 K. The inlet pressure for the hot w..

  Find minimum initial tension require at commissioning stage

Select a suitable belt and, ignoring the elongation at fitting but using the guide mass/unit length, calculate the power transmitted if the maximum permissible tension is 1kN and the coefficient of friction is 0.25 if the motor rotates at 1450rpm

  Calculate the thermal efficiency based on the net work and

six kilograms of co2 executes at carnot cycle in a piston-cylinder assembly. the minimum and maximum gas temperatures

  If the cooling water enters at a temperature of 20 degree c

one way to decrease the power needed to compress a gas using a compressor is to encompass the compressor in a water

  Calculate the adiabatic flame temperature attained

Calculate the adiabatic flame temperature attained when methane at 298k, is combusted (a) with oxygen in the molar ratio air/CH4 = 9.524. Assume that CO2 and H2O are the products of the combustion. The adiabatic flame temperature is that temperature ..

  A 1000 ft3 glass bottle is initially evacuated then has

a 1.000 ft3 glass bottle is initially evacuated then has 1.000 g of water added that eventually comes to equilibrium at

  Find the critical speed when the trailer is traveling over

the springs of an automobile trailer are compressed 10.6 cm under its weight. find the critical speed when the trailer

  Determine the amount of heat rejected

A fixed mass of saturated water vapor at 400 kPa is isothermally cooled until it is a saturated liquid. Perform a closed system, energy analysis (e.g. 1st Law analysis) on the system to determine the amount of heat rejected during this process in kJ/..

  A bug is on the rimof a disk of diameter 13 in that moves

a bug is on the rimof a disk of diameter 13 in that moves from rest to an angular speed of 70 revmin in 5.2 s.what is

  What is the spring rate of each what force is required to

two steel compression coil springs are to be nested. the outer spring as an inside diameter of 1.5 in a wire diameter

  Why do we stipulate a long plate

Compute the shear buckling coefficient for a long, simply-supported, rectangular plate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd