Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1. The three isometric axes are: vertical and two axes 30 degrees from horizontal.2. Oblique projection is a perspective projection method.3. Isometric view represents a parallel projection method.4. In orthographic, incline and oblique planes are the same.5. The intersection of two planes is represented either by a continuous or a hidden line.6. A secant line is a straight line that goes through the center of a circle.7. A secant touches a circle at one point.8. An angle bisector is the locus of all points equal-distant from the two sides of an angle.9. The center of an arc tangent to two lines is on the angle bisector of the two lines.10. Each of the angles of a pentagon is 60 degrees.11. Each of the angles of a hexagon is 120 degrees.12. The intersection of a plane and a cylinder is a circle if the plane & cylinder are perpendicular13. Ellipse is a geometry with major and minor axes.14. The diameter of an ellipse is twice as its radius.15. The intersection of an incline plane and cylinder is either an ellipse or a hyperbola.16. The top view in orthographic projection shows the width and depth of an object.17. In third-angle projection, the projection plane is between the viewer and the object.18. There are four standard orthographic views corresponding to the four sides of a cube.19. Perspective projection is used when the object spans a large distance, e.g., a house or a bridge.20. In first-angle projection, he right side view is placed to the right of the front view.21. Given a line and a point , the point is the center of only one circle tangent to the line.22. Constructing an arc tangent to two circles is always possible provided the fillet radius in reasonable.23. A polygon can always be inscribed in a circle.24. An octagon has eight equal sides.25. A circle, passing through 3 points, can always be constructed, if three points are not on a straight line.26. The smallest circle, passing through two points, is one where the two points form a diameter.27. Two orthographic views are sufficient to describe the shape of a cylinder.28. The 3 mayor axes in oblique projection are: vertical, horizontal and 30 degrees with horizontal.
A glass jar is heated in an oven and sealed when the air pressure is 103 kPa and the temperature is 105 C. Find the absolute, gage, and vacuum pressures in the jar when it cools to 20 C.
The elastic ball bounces down a flight of rigid stairs. Determine the height h of the steps if all the trajectories between successive steps are identical. Use e = 0.85 and the initial velocity 6 m/s.neglect friction. (Theta=70 degrees)
What kind of soil labs are good for the construction which is underlying the wet clay is dense sand. For example, compaction, and so on.
Long Line: the slope distance and zenith angle measured from point a to point b were 17,685.20 ftand 93degrees 13' 46" . The instrument and reflector heights were equal. If the elevation of the point A is 1854.43 ft above the MSL Datum
water is flowing at a velocity of 10ft/s and a depth of 10ft in a channel of rectangular section. find the change in depth and in absolute water level produced by a smooth upward step of 1 ft. a smooth downward step of 1 ft in the channel bed.
Determine the mass flowrate through boiler needed to produce 5000KW of power.
A 4.00-cm-diameter, 0.80-m long rod of aluminum 7075-T6 is subjected to an axial tensile force with a factor of safety of 1.75. The yield stress and modulus of elasticity of aluminum 7075-T6 are 500. MPa and 210. GPa, respectively.
A 300 mm diameter pipe is placed in a 3 m deep rectangular trench that is 0.60 m wide. The trench is backfilled with clay that has a bulk unit weight of 18.8 kN/m3. Compute the dead load due to backfill that the pipe must support.
For a mixture 10 mol % methane 20 mol % ethane 70 mol % butane at 50 degrees Fairenheit determine the bubble point pressure
The factory will use a 4 ft deep on-site lagoon to stabilize the waste with a loading rate of 20 lb BOD/acre-day. Part a) What is the total BOD loading per day?
Normal load at failure was 93.8N with a maximum shear load of 38.7N. Find stresses on the failure plane, sketch a graph showing these on the shear stress and normal stress axes. Find the friction angle and shear strength.
Three days later, Abu sees his solicitors and executed the transfer of his said bungalow to Abdul Samad at the said value. Two month later, Abdul Samad expelled Abu from the religious group. Abu now wants to set aside the sale of his bungalow.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd