Explain the effect of insulating a hot surface

Assignment Help Chemical Engineering
Reference no: EM131319648

Question 1.

(a) Give three examples for each of natural (free) convection and forced convection which occur in industrial processes.

(b) The Grashof number and the Reynolds number appear in most correlations of experimental data for convective heat transfer. Explain, in a maximum of 150 words, the mechanisms of natural and forced convection with particular reference to the above non-dimensional groups.

(c) An appropriate correlation for heat transfer by natural convection from a horizontal pipe to the atmosphere is

Nu = 0 53Gr0.25Pr0.25

where Gr = αρ2d3(Ts - Tf)g/μ2

and  Pr = cpμ/k

Show that the above correlation can be simplified to

h = 1.34((Ts - Tf/d)0.25Wm-2K-1

when air has the values listed below

α = 3.077 x 10-3k-1 ρ= 1.086 kg m-3, cp =1.0063 kJ kg-1K-1

k= 2.816 x 10-5 kW m-1 μ = 1.962 x10-5 kg m-1s-1

(d) The outer surface of the insulation on a horizontal steam pipe has a radius of 50 mm and is at a temperature of 90°C The atmospheric air surrounding the pipe is at a temperature of 14°C. and has the property values listed in part (c) above. Estimate the rate of heat loss by natural convection to the atmosphere by each metre length of pipe.

Question 2: (a) Explain how heat is bst from a hot surface to the surrounding air.

(b)

(i) Explain the effect of insulating a hot surface.
(ii) What is meant by the economic thickness of lagging?

(c) What is the purpose of a silvered coating. usually of a good conductor, on the outside of most insulation?

Question 3: Butanol at a temperature of 28°C is pumped at a velocity of 14 m s-1 through a 100 mm diameter tube kept at a wall temperature of 90°C The properties of butanel are given below.

Determine the convective heat transfer coefficient (you will find the appropriate correlation in the lessons).

Data:

p = 950 kg m-3

cp = 2.142 kJ kg-1 K-1

μ = 2.9 X 10-3 kg m-1 s-1 at 28°C

μ = 12 x 10-3 kg m-1 s-1 at 90°C

k = 2.4 X 10-4 kW m-1 K-1

Question 4. (a) Process water with a specific heat capacity of 4.182 kJ kg-1 K-1 flows at a rate of 0.050 kg s-1 through a heat exchanger where its temperature is increased from 16°C to 85°C. Heat is supplied by exhaust gases (mean specific heat capacity 1.075 kJ kg-1 K-1) which enter the heat exchanger at a temperature of 420°C. If the mass flowrate of the exhaust gases is 0.044 kg s-1, determine their outlet temperature.

(b) The heat exchanger in Question 1 (a) above is of the double-pipe type, and the fluids are in counter flow. If the overall heat transfer coefficient is 35 W m-2 K-1, calculate the size of the heat transfer surface.

(c) What would be the new heat transfer area if the fluids were in parallel flow?

(d) Describe what is wrong with the sketch of the temperature profiles for the parallel-flow heat exchanger shown in FIGURE 1 and draw the correct version.

740_Fig.png

Question 5. (a) The data in TABLE 1 below relates to a specific heat exchanger. A reliable colleague has looked up an effectiveness chart and says that the effectiveness in the given operating conditions is 0.82.

 

'Hot' fluid

'Cold' fluid

Mass flowrate kg s-1

 

0.7

 

0.6

Specific heat capacity kJ kg-1 K-1

1.8

4.2

Inlet temperature

°C

 

140

 

15

TABLE 1

Area of heat transfer surface 14 m2.

Overall heat transfer coefficient 360 W m-2 K-1. Determine:
(i) the two outlet temperatures
(ii) the heat transfer rate.

(b) Another colleague, who is not altogether reliable, has analysed the heat exchanger, referred to in Question 2 (a), using the correction- factor method and he claims that the correction factor is 0.595. Confirm whether he is correct or not.

Question 6. (a) Dry saturated steam at a temperature of 180ºC is to be produced in a fire tube boiler from the cooling of 50 000 kg h-1 of flue gases from a pressurised combustion process. The gases enter the tubes of the boiler at 1600ºC and leave at 200ºC. The feed water is externally preheated to 180ºC before entering the boiler.

The mean specific heat capacity of the flue gases is 1.15 kJ kg-1 K-1. The latent heat of vaporisation of the water at 180ºC is 2015 kJ kg-1. Feed water temperature = 180ºC.

Determine the amount of steam produced per hour, if the total heat loss is 10% of the heat available for steam raising.

(b) The overall heat transfer coefficient based on the outside area of the tubes is given as 54 W m-2 K-1. Determine the area of heat transfer required to perform this duty.

(c) The tubes within the boiler are to be 25 mm inside diameter with a wall thickness of 3 mm. The average flue gas velocity through the tubes to maintain the overall heat transfer coefficient value and to minimise pressure losses is to be more than 22 m s-1 and less than 28 m s-1.

Assuming that the average density of the flue gases is 1.108 kg m-3, calculate:

(i) the minimum and maximum number of tubes in each pass

(ii) the overall length of tubes at each of these numbers of tubes

(iii) the minimum number of tube passes in each case, if the length of a boiler tube is to be less than 5 metres.

Question 7: Liquid ammonia is heated as it flows at a mean velocity of 2 ms-1 through a circular pipe. The pipe, which has an internal diameter of 75 mm, is at a uniform temperature of 27°C, and the ammonia at a section 12 m from the inlet to the pipe has a temperature of -23°C. Use the following information to estimate the local heat transfer flux at l = 1.2 m. Note, the properties of ammonia liquid have been taken at -23°C, except where stated.

Liquid ammonia properties:

Density = 600 kg m-3

Specific hes capacity = 4.86 kJ kg-1 K-1

Dynamic viscosity (at 27°C) = 1.19 x 10-4 kg m-1

Dynamic viscosity = 2.05 x 10-4 kg m-1s-1

Thermal conductivity = 5.11 x 10-4 kW m-1s-1

Heat transfer correlations:

Nu = 1.86Re1/3Pr1/3(d/l)1/3(μ/μw)0.14 for turbulent flow.

Nu = 0.023Re0.8Pr0.33an for turbulent flow.

Question 8:

(a) Explain what is meant by an 'overall heat transfer coefficient'.

(b) Explain what is meant by fouling and what its effect will be on the value of the overall heat transfer coefficient.

(c) A heat exchanger is to be aced to heat a process liquid within the tubes using saturated steam at 100°C. The tubes have an inside diameter of mm and outside diameter of 22 mm. It is estimated that the inner surface heat trawler coefficient will be 4.2 kW m-2 K-1 and the outer surface heat transfer coefficient will be 15.4 kW m-2 K-1 when the exchanger is clean. In order to allow for possible fouling during use you should assume a fouling factor of 1.12 x 10-4 m2 K W-1 win be applicable.

Estimate:

(i) the overail heat transfer coefficient in use

(ii) the heat transfer rate when the relevant average temperature difference between steam and fluid is 50°C and the heat exchanger has 100 tubes eac h of 5 m in length.

Question 9:

A fuel gas consists of 75% butane (C4H10), 10% propane (C3H8) and 15% butene (C4H8) by volume.

It is to be fed to the combustion chamber in 10% excess air at 25ºC, where it is completely burnt to carbon dioxide and water. The flue gases produced are to be used to generate 5 bar steam from water at 90ºC.

With the aid of the data at the end of the question, steam tables and the enthalpy table given in the Appendix of lesson HTC - 4 - 2:

(a) Write balanced equations for the combustion of each component of the fuel gas.

(b) Explain the need for excess air.

(c) Determine the actual fuel:air ratio

(i) by volume
(ii) by mass.

(d) Calculate:

(i) the net calorific value (CV) per m3 of the fuel/air mix at 25ºC
(ii) the net calorific value (CV) per kmol of the fuel/air mix at 25ºC.

You will need graph paper, a calculator, a copy of appendix 1 from lesson HTC- 4 - 2 and access yo steam tables to answer this TMA.

Question 10:

A fuel gas consists of 75% butane (C4H10), 10% propane (C3H8) and 15% butene (C4H8) by volume.

It is to be fed to the combustion chamber in 10% excess air at 25ºC, where it is completely burnt to carbon dioxide and water. The flue gases produced are to be used to generate 5 bar steam from water at 90ºC.

With the aid of the data at the end of the question, steam tables and the enthalpy table given in the Appendix of lesson HTC - 4 - 2:

(a) Write balanced equations for the combustion of each component of the fuel gas.

(b) Explain the need for excess air.

(c) Determine the actual fuel:air ratio

(i) by volume
(ii) by mass.

(d) Calculate:

(i) the net calorific value (CV) per m3 of the fuel/air mix at 25ºC
(ii) the net calorific value (CV) per kmol of the fuel/air mix at 25ºC.

(e) Determine the composition of the flue gases by volume (assuming the inlet air is dry):

(i) on a wet basis
(ii) on a dry basis.

(f) Determine the maximum flame temperature.

(g) State how varying the amount of excess air may affect the flame temperature.

(h) Determine the ‘furnace efficiency' if the flue gases leave the boiler at 300ºC.

(i) If 5% of the heat available for steam production is lost to the atmosphere, determine the amount of steam raised per hour when the total flow of flue gases is 1400 kmol h-1.

(j) Determine the dew point temperature assuming that the flue gas pressure is 1.00 bar and the inlet air:

(i) is dry

(ii) contains 0.8 kg water per kmol of air at the temperature of the inlet air.

(k) If the flue gases exiting the boiler are used to preheat the water fed to the boiler from a temperature of 28ºC to 90ºC and assuming:

- a mean specific heat capacity for water over this temperature range to be 4.2 kJ kg-1 K-1

- a mean molar heat capacity for the flue gases up to 300ºC to be 31 kJ kmol-1 K-1

- 10% of the heat required to heat the water is lost in the heat exchanger

- all water entering the system is converted to steam

determine the final outlet temperature of the flue gas and state if the dew point will be reached in both of the cases given in part (j).

(l) Give two advantages of preheating the water in this way and one disadvantage.

(m) Give two reasons why the presence of any sulphur in the fuel mix would be undesirable.

Data:

Net calorific value (MJ m-3) at 25ºC of:

Butane (C4H10) = 111.7 MJ m-3

Butene (C4H8) = 105.2 MJ m-3

Propane (C3H8) = 85.8 MJ m-3

Air is 21% oxygen, 79% nitrogen by volume and 23.3% oxygen and 76.7% nitrogen by mass.

Atomic mass of C = 12, O = 16, N=14 and H = 1.

Question 11. (a) A small reheating furnace wall consists of 200 mm of firebrick. The inner surface of the wall is at a temperature of 320 °C and the outside temperature is 35 °C. Calculate the rate at which heat is transferred, by conduction, through unit area of the wall. The thermal conductivity of the firebrick used can be taken as 1.8 W m-1 K-1.

If the outside surface area of the furnace is 50 m2 estimate the heat losses through the furnace wall per hour.

(b) A furnace wall consists of three layers of material as shown below.

2261_Fig.jpg

The thermal conductivities are:

firebrick = 1.15 W m-1 K-1

insulating brick = 0.17 W m-1 K-1

ordinary brick = 0.62 W m-1 K-1

Calculate:

(i) the thermal resistance of each layer

(ii) the heat loss per unit area

(iii) the temperature at the two interfaces.

Question 12. A surface condenser consists of a bank of horizontal tubes contained within a steel shell. Saturated steam is condensed on the outside of the water-cooled tubes and the condensate drains to the bottom of the shell where it collects and is pumped out. Tubes towards the bottom of the tube bank are drenched by the water draining from above, and the average thickness y (metres) of the laminar water film flowing over a tube is given by the equation

y = 1.39 (μΓ/ρ2g)1/3

where Γ is the mass flowrate of water falling onto unit length of tube, and the other symbols have their usual meanings.

Since the water falling onto the top of the tube divides and flows down both sides, the average Reynolds number is given by

Re = 2Γ/μ

Assuming that local condensation does not significantly increase the film thickness on the drenched tubes, use the following data to find the heat flux and condensation rate per unit area for one particular tube.

Question 13. A pipe of outside diameter 200 mm is lagged with an insulating material of thermal conductivity 0.06 W m-1 K-1 and thickness 75 mm. The pipe carries a process fluid at a temperature of 300 °C and the average temperature of the outer surface of the lagging is 45 °C.

(a) Estimate the rate of heat loss per metre length of pipe.

(b) Explain why the thermal resistance of the pipe wall can be ignored.

Question 14. A pipe carrying superheated steam at 300 °C has an outside diameter of 120 mm and is lagged with two layers of insulating material. The first layer (adjacent to the outer pipe wall) is 25 mm thick and has a thermal conductivity of 0.072 W m-1 K-1. The second layer (covering the first layer) is 20 mm thick, has a thermal conductivity of 0.051 W m-1 K-1 and an outside temperature of 28 °C.

Estimate the rate of heat loss per metre length of pipe (assume the thermal resistance of the pipe wall is negligible).

Reference no: EM131319648

Questions Cloud

Short paper on kant : Short Paper on Kant. Kant famously--and controversially--argued that some knowledge is synthetic a priori. Can you explain in your own words what Kant might have meant by this, and can you give an example of the sort of knowledge that Kant believe..
Discuss your experience of human-computer interface : This assignment requires you to write a paper to discuss your experience of human-computer interface. This paper should cover but not limited to topics such as what features you find are most user friendly.
What is the mean number of rolls until the next six : Fred rolls an unbiased six-sided die once per second, noting the occasions when the outcome is a six.
Identify the null hypothesis and alternative hypothesis : (a) Identify the null hypothesis and the alternative hypothesis. (b) Determine the test statistic. Show all work; writing the correct test statistic, without supporting work, will receive no credit. (c) Determine the P-value for the test. Show all..
Explain the effect of insulating a hot surface : Explain the effect of insulating a hot surface - What is meant by the economic thickness of lagging and determine the convective heat transfer coefficient -Describe what is wrong with the sketch of the temperature profiles for the parallel-flow hea..
Expected frequencies of winners from prize : A. What are the expected frequencies of winners from each prize? B. Conduct a significance test to determine whether the winners of the prizes were distributed throughout the classes as would be expected based on the percentage of students in each..
Explain the basic tenets of each religious tradition : Explain the basic tenets of each religious tradition, and how they define an individual's role in the world and his/her relationship with the deity
Existence of agency problems between managers-share holder : One reason for the existence of agency problems between managers and share holder is that: Which of the following is least likely to be part of an Annual Report?
How should disagreements about usability be resolved : What do you believe are the appropriate criteria for assessing usability? Who should make such judgments? How should disagreements about usability be resolved?

Reviews

Write a Review

 

Chemical Engineering Questions & Answers

  Could it be a genuine rembrandt

Your painting showed a carbon-14 activity of 15.1 counts per minute per gram. Could it be a genuine Rembrandt?

  Estimate the entropy change of the propane

Propane gas at 22 bar and 423 K is throttled in a steady-state flow process to 1 bar. Estimate the entropy change of the propane caused by this process. In its final state, propane may be assumed to be an ideal gas.

  Main objectives of the computer aided modeling

Main objectives of the computer aided modeling and simulation system - Critically analyze the applicability, domain, features and advantages of the various systems available.

  Is rusting a moderate reaction

Is rusting a moderate reaction? Rusting is an example of what reaction?

  Calculate the mass of the metal in gr

Calculate the mass of the metal in gr than can be prepared  from 150 grams of aluminum and 250 grams  of iron (iii) oxide

  Estimate the annual operating cost

Estimate the annual operating cost of providing refrigeration to a condenser with duty 1.2 MW operating at -5 ºC. The refrigeration cycle rejects heat to cooling water that is available at 40 ºC, and has an efficiency of 80% of the Carnot cycle ef..

  Improving the blood compatibility of biomaterials

Describe two potential options for improving the blood compatibility of biomaterials, discuss their potential for ultimately improving blood compatibility and describe any engineering challenges to implementing these to practice.

  Calculate the amount of heat and work involved

Following a procedure analogous to that in Example 5.2, obtain an expression for the coefficient of thermal expansion based on the van der Waals equation of state. Use the result to calculate the value of β for oxygen at 20 °C, 30 bar.

  Calculate the atomic weight

Calculate the atomic weight (in amu) of an element (X), given the following data: 24X : 24.000 amu at 0.7879 fractional abundance 26X : 26.000 amu at 0.1017 fractional abundance 25X : 25.000 amu at 0.1113  fractional abundance

  Calculate the work done in the isothermal reversible

Calculate the work done in the isothermal reversible expansion of one mole of CH4 (g) from 1.00 dm3 to 10.00 dm3 at 300 K. Treat methane as a van der Waals gas. The van der Waals gas constants for methane are: a=2.3026 dm6⋅bar⋅mol−2 and b=0.043067 dm..

  What is the maximum efficiency of a steam

What is the maximum efficiency of a steam engine operating between 20° C and the boiling point of water, 100 °C, at one atmosphere?

  How does emergent behavior lead to disease

Emergent behavior is present in normal cellular and pathologic processes. How does emergent behavior lead to disease?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd