Explain the difference between these two probabilities

Assignment Help Mechanical Engineering
Reference no: EM131173761

Suppose that a product is composed of 25 identical and probabilistically independent parts. Assume that this product is manufactured through the use of a k-sigma process with a process mean that is 1.25 standard deviations above the target mean. Assuming that k = 3, what proportion of these multipart products are not within specification limits? Answer this question again for the case where k = 6. Explain the difference between these two probabilities.

Reference no: EM131173761

Questions Cloud

Calculate the internal rate of return for each project : BUACC3701: Financial Management Calculate the Net Present Value for each project and calculate the Internal Rate of Return for each project
Comment on any unusual aspects of the histogram : The file P20_47.xlsx contains the measured diameters (in inches) reported by the prod uction foreman of 500 rods produced by Rodco.
What was senior management typical approach toward quality : Prior to the advent of the total quality management concept, what was senior management's typical approach toward quality? What has led to the more comprehensive strategic view about total quality management?
Estimate cp and the probability of meeting specifications : Eleven samples of size 3 were taken in an effort to monitor the voltage held by a regulator. The data are in the file P20_44.xlsx. A regulator meets specifications if it can hold between 40 and 60 volts.
Explain the difference between these two probabilities : what proportion of these multipart products are not within specification limits? Answer this question again for the case where k = 6. Explain the difference between these two probabilities.
Design a combinational circuit that converts a binary number : Design a combinational circuit that converts a binary number of four bits to a decimal number in BCD. Note that the BCD number is the same as the binary number as long as the input is less than or equal to 9.
Construct sixteen-bit parallel adder with four msi circuits : Construct a 16-bit parallel adder with four MSI circuits, each containing a 4-bit parallel adder. Use a block diagram with nine inputs and five outputs for each 4-bit adder.
Compute the pressure produced in the oil : Compute the pressure produced in the oil in a closed cylinder by a piston exerting a force of 2500 lb on the enclosed oil. The piston has a diameter of 3.00 in.
Create a plot for the interest rate over time : Create a plot for the interest rate over time and find the linear equation that models the change in the interest rates over the 12 month

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Calculate the mass flow rate of air and the required power

air is compressed by an adiabatic compressor from 100 kpa and 20 degc to 1.8 mpa and 400 degc. air enters the

  The pressure in a partially evacuated enclosure is 268 in

the pressure in a partially evacuated enclosure is 26.8 in hg vacuum when the local barometer reads 29.5 in hg.

  A rigid insulated vessel is divided into two compartments

a rigid insulated vessel is divided into two compartments connected by a valve. initially one compartment occupying

  Describe external threading operations explain the external

describe external threading operations. explain the external threading operation in details. why is it important to

  Cross-sectional area of the wire and by e the modulus

The uniform wire ABC, of unstretched length 2l, is attached to the supports shown and a vertical load P is applied at the midpoint B. Denoting by A the cross-sectional area of the wire and by E the modulus of elasticity, show that, for

  The partition is then removed eventually the entire rigid

a mass of 4.0 kg of r-134a at p1140 kpa and t1 20 cis contained in a gas tight frictionless piston cylinder device. the

  The tank is connected by a valve to a supply line where air

an insulated 0.15 m3 rigid tank initially contains air at 27c and 3 bar. the tank is connected by a valve to a supply

  What is most nearly the velocity of the block at position b

The 52 kg block shown starts from vast at position A and slides down the Inclined plane to position B. What is most nearly the velocity of the block at position B

  Determine by direct integration the mass moment

Determine by direct integration the mass moment of inertia with respect to the y axis of the tetrahedron shown, assuming that it has a uniform density and a mass m.

  Dtermine the final volume v2 of the gas pv constant p1

a gas contained in a piston cylinder assembly undergoes a process from state 1 to state 2 defined by the following

  The bed of the truck is 03 and static friction is not

a truck traveling at vo 60 mph when the driver applies the brakes to come to stop the deceleration of the truck is

  Will the same magnus force be created to power the boat

A freely (zero friction) rotating cylinder (mounted on a vertical axis) is placed on a model boat instead of a sail. The Magnus force that is created is used to power the boat. A fan is mounted on the boat to provide airflow over the cylinder.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd