Estimate work done by heart to keep the blood circulating

Assignment Help Mechanical Engineering
Reference no: EM13708067

Estimate the work done by the heart to keep the blood circulating.

Qblood = 5.0 L/min

Pblood = 1.056 kg/L

u (pulmonary vein) = 0.139 m/s from lungs; 6 mm Hg

u (aorta) = 0.333 m/s to body; 95 mm Hg

u (vena cava) = 0.104 m/s from body; 0 mm Hg

u (pulmonary artery) = 0.208 m/s to lungs; 15 mm Hg

Assumptions

1. The fluid that flows through the heart has a uniform velocity profile.

2. The system can be modeled as steady-state with one inlet and one outlet.

3. Neglect frictional loses in the pumping heart.

4. No reactions occur.

5. Negligible elavation changes in the heart (i.e., the points all lie at the same height in the heart)

6. The blood is inviscid and incompressible.

Reference no: EM13708067

Questions Cloud

What is the resolution error-input frequency : What is the resolution error (or quantization error) if a +/- 10V DAQ card has a 3 bits? If a 10 Hz signal is sampled at 45 Hz. For an input frequency of 10 Hz, If you want at least 20 points/second, what should your sampling frequency be? If you wan..
Determine the thrust required tr to sustain this flight : An airplane weighing 70000 lb is in a cruise flight (constant altitude, constant velocity, level flight) at an altitude of 30000 ft, with a velocity of 0.5 Mach. Its wing area is 4000 ft2. Given the drag polar of the airplane as CD=CD,0+0.05CL2; CD,0..
Determine the atomic hydrogen to carbon ratio of the fuel : A new liquid fuel with formula CHz is proposed for use in spark-ignition engines. To determine the fuel properties, a sample of fuel at 25 degress C was placed in a constant volume bomb calorimeter. Oxygen at 25 degress C was admitted to the bomb and..
Calculate the absorbed radiation per unit area of absorber : For an hour 11 AM to 12 noon on a clear winter day, IB = 1.38 MJ/m2, and ID = 0.41 MJ/m2. Ground reflectance is 0.6. For this hour, the incidence angle ? for the beam radiation is 17°, and RB = 2.11. A collector with one glass cover is sloped 60° and..
Estimate work done by heart to keep the blood circulating : Estimate the work done by the heart to keep the blood circulating. The fluid that flows through the heart has a uniform velocity profile. The system can be modeled as steady-state with one inlet and one outlet. Neglect frictional loses in the pumping..
Consumers benefit more from a tariff or a quota on imports : Would consumers benefit more from a tariff or a quota on imports? Provide one (1) supporting fact to support your response.
Calculate the temperature of water exiting absorber tubes : Calculate the temperature of the water exiting the absorber tubes. Calculate the rate of exergy transfer accompanying the heat transferred from the absorber tubes to the water. Calculate the amount of exergy destroyed in the absorber tubes.
What is the maximum power output of the turbine : An energy conscious couple decides to dam up the creek flowing next to their cabin and estimates that a head of 7m can be established above the exit to a turbine they bought on eBay. The creek is estimated to have a flow rate of 0.9 m3/s. What is the..
Dna purification : Describe the similarities and differences in the DNA purification that you performed versus theprocedure described by Avery in his initial paper

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A long 10 cm square copper bar is bounded by 260c gas flows

a long 10 cm square copper bar is bounded by 260c gas flows on two opposing sides. these flows impose heat transfer

  The water is cooled by air that enters at 075 kgs and 300 k

an automobile radiator may be viewed as a cross-flow heat exchanger with both fluids unmixed. water with a flow rate of

  Determine the turbine efficiency and the combined

it is proposed to generate electrical power by installing a hydraulic turbine-generator at a site 70 m below the free

  At the end of each year th amount in the account is 105

suppose that 1000 is deposited into an account that pays 5 intrest per year. at the end of each year th amount in the

  Determine the number of cycles per minute

Determine the number of cycles per minute

  In moles of an ideal gas a ad 1-n moles of an ideal gas b

in moles of an ideal gas a ad 1-n moles of an ideal gas b each at 1 atm pressure are mixed at total constant pressure.

  Determine the work and heat transfer

determine the work and heat transfer, each in kJ. sketch the process on p-v and T-s coordinates. Associate the work and heat transfer with areas on these diagrams.

  An engineer is designing a horizontal rectangular conduit

engineering fluid mechanics 9th editionauthors crowe elger williams roberson problem 9.62 pg 313.an engineer is

  What is a beam

What is a beam? What factors determine the maximum load that it can take without failure?

  Draw the profile of the elctromagnetic torque tem required

nloadnmotor 3 inertia of motor1.2 kgm2 inertia of load 10 kgm2 dampening and load torque can be neglected.draw the

  The total curvilinear distance down the conveyor is 298

the conveyor carries cartons down five meters to the first floor delivery room on rollers. the radius of the conveyor

  Determine the work done during the process a by plotting

gas with an initial volume of 0.36 m3 is slowly compressed to a final volume of 0.16 m3 by a process during which the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd