Estimate the stopping distance required traveling northbound

Assignment Help Civil Engineering
Reference no: EM13561563

Estimate the stopping distance required traveling northbound along University Drive towards campus assuming you are traveling at 40 mph under normal conditions. Next, because it is after midnight and you have been studying for the last 8 hours, assume that you are experiencing extreme fatigue and that your perception reaction time is 3.5 seconds. Next, recalculate both of your responses assuming a 5 percent upgrade. Discuss the results.

Reference no: EM13561563

Questions Cloud

Can you find bod10 from this test : During a BOD test, 2 mL of waste water having a DO of 0 was mixed with 298 mL of dilution water having a DO of 8.9 mg/L. After 5 days and 20 days, it was noted that the DO of the test bottle was 4.0 and 2.5 respectively,
Make a preliminary estimate of the length and elevation : A 5-ha residential development with 0.4-ha lots is to be drained such that the first 25mm of runoff is retained onsite and the postdevelopment peak discharge rate from the site is not to exceed 1m^3/s for thje 25-year 1-d rain event. The natural soil..
The peak time is 1 hour and the recession times is 2 hours : Route a trianglular hydrograph through a 100 foot wide rectangular channel with a bed slope of 0.015 and a Mannings n of 0.035.  Take a distance between cross-sections of 3000 ft.
Determine their common velocity just after the collision : A steel column has a total unbraced height of 14 ft and carries an axial LRFD load of 950 kips. The column ends are fixed. Select an economical HSS 14x14 for this column.
Estimate the stopping distance required traveling northbound : Estimate the stopping distance required traveling northbound along University Drive towards campus assuming you are traveling at 40 mph under normal conditions.
Explain the working principles of two tests that can : Should the soil be compacted at the dry of optimum or at the wet of optimum condition in order to minimize the swelling potential? Briefly explain the reason for your answer.
Calculate the percentage of change in total volume : A montmorillonite clay has a liquid limit of 160, a plastic limit of 75 and a shrinkage limit of 10. Calculate the percentage of change in total volume with respect to its initial volume when a specimen of this clay is completely dried from a water c..
Calculate the coefficient of consolidation and compression : Briefly explain the difference between piezometer and tensiometer with respect to the working principle, special design consideration and limitation of the instrument.
Description marks out : Description Marks out

Reviews

Write a Review

Civil Engineering Questions & Answers

  Force that cause stress-free

The rigid bar abcd is supported by a pin at B and restrained by identical steel bars at C and D, each of area 250mm 2 . if the temperature is increased by 8 0 C, find out the force P that will cause the bar at c to be stress-free.

  Draw the influence line for the support reaction

Draw the influence line for the support reaction at A and calculate the support reaction at point

  Derive a relationship to evaluate the discharge

Using Buckingham-Pi method, derive a relationship to evaluate the discharge, Q, over a rectangular notch as a function of the width of notch, b, acceleration due to gravity, g, fluid density

  Determine the minimum entropy change of the thermal energy

Heat is now added until the quality is 40 percent. Determine the minimum entropy change of the thermal energy reservoir supplying this heat.

  Determine the critical load of a steel tube

Determine the critical load of a steel tube that is 5 m long and has a 100-mm outer diameter and a 16-mm wall thickness. Use E = 200 GPa.

  What is the time-mean speed and space-mean speed for vehicle

Assume you are an observer standing at a point on the track for a period of 30 minutes and are recording the instantaneous speed of each vehicle as it crosses your point. What is the time-mean speed and space-mean speed for these vehicle

  Estimate the supply pressure required at the flow rate

Water, at volume flow rate Q=20 L/s, is delivered by horizontal fire hose and nozzle assembly. The hose (L = 100m, D = 75 mm, and e/D = .004) is made up of five 20 m sections joined by couplings

  A ferric chloride dosage of 40 mg/l and an equivalent dosage

A ferric chloride dosage of 40 mg/l and an equivalent dosage of lime are used to coagulate a water.

  Determine probability that at least 7 will ride in carpools

suppose 76% of all commuters ride to work in carpools. if eight workers are randomly selected, find the probability that at least 7 will ride in carpools

  Determine shear stress at each wall and max shear stress

The velocity distribution for the flow of oil (SAE 20W) at 150 degrees between two plates is given by y(y-4) mm/s, where y is measured in mm and the space between the plates is 4mm. Determine the shear stress at each wall and the maximum shear str..

  Whate are the relative fractions of ferrite and cementite

A Fe-.25 w/o Carbon alloy is sloly cooled to 700 degrees C. What is the composition of the Ferrite(alfa) phase and what is the compositon of the cementite(Fe3C) phase. Whate are the relative fractions of ferrite and cementite

  Determine what is the final river temperature downstream

A toothpaste factory situated on a large river disposes of a waste water containing villiamite (NaF) to the river on a continuous basis. The minimum flow in the river is 210 m3/s, and the discharge rate from the treatment plant is 12.5 m3/s.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd