Estimate the pullout length required for each reinforcement

Assignment Help Civil Engineering
Reference no: EM13304651

Three reinforcements are being considered for an MSE wall: A continuous geogrid having a reinforcement coverage ratio equal to 100 percent. A continuous metallic grid consisting of W4 bars having a diameter equal to 5.7 mm, a distance between longitudinal bars equal to 150 mm, a distance between transverse bars equal to 300 mm, and a reinforcement coverage ration equal to 100 percent A ribbed steel strip having a width equal to 50 mm, a distance between strips equal to 0.75 m, and a reinforcement coverage ration equal to 6.67 percent Estimate the pullout length required for each reinforcement to obtain a pullout resistance equal to 10 kN per meter width of the structure at a depth equal to 1 m below the top of the structure

Reference no: EM13304651

Questions Cloud

What is the amplitude of the ossilation : An air-track glider is attached to a spring. The glider is pulled to the right and released from rest att = 0. what is the amplitude of the ossilation
Calculate the volatility of a portfolio : Using the data in the following table, and the fact that the correlation of A and B is .00073, calculate the volatility (standard deviation) of a portfolio that is 60% invested in stock A and 40% invested in stock B.
What is the velocity when it reaches the bottom : A 2kg uniform cyclinder is released at the top of a 1.53 m 11 degree incline. What is the velocity when it reaches the bottom
What is the maximum debt ratio the firm can use : It can borrow at a rate of 7.5%, but the bank requires it to have a TIE of at least 4.0, and if the TIE falls below this level the bank will call in the loan and the firm will go bankrupt. What is the maximum debt ratio the firm can use?
Estimate the pullout length required for each reinforcement : A continuous geogrid having a reinforcement coverage ratio equal to 100 percent. A continuous metallic grid consisting of W4 bars having a diameter equal to 5.7 mm, a distance between longitudinal bars equal to 150 mm, a distance between transvers..
Obtain the density of mobile electrons in the material : The Hall effect can be used to determine the density of mobile electrons in a conductor. Find the density of mobile electrons in the material
Determine the volume of sludge after filtration : Assume that the sludge does not change density during filtration and that liquid removed from the sludge contains no sludge. Using mass-balance method. determine the volume of sludge after filtration.
What is the linear distance on the screen : In a double-slit experiment, what is the linear distance on the screen between adjacent maxima if the wavelength is 538 nm
Compare the reactor volume required to achieve efficiency : Compare the reactor volume required to achieve 95% efficiency for Completely Mixed Flow Reactor (CMFR) and a Plug Flow Reactor (PFR) for the following conditions. steady-state, first-order reaction, flow rate = 14m3 / day.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  How long ago did the dumping stop

the flow rate into the lake is 10 m3/s, the surface area of the lake is 1 x 107 m2, and the rate of evaporation from the lake is 6 cm/wk, how long ago did the dumping stop?

  Engineering ethics and concept and cases

what is the engineering ethics case related to civil engineering with reference and discuss all the engineering ethics issues which covered the "Engineering etics concepte and cases?

  Determine what is the thermal stress generated in the rod

The ¼" thick 6061?T6 aluminum bar is subjected to a tensile force of P = 5 kips. b = 4"; c = 1.5"; d = 2.5"; and the fillet radii are 1". a) Determine the maximum stress in the bar. b) What is the lateral strain in the 1.5" wide section

  At what flow rate should the farmer pump the water

A farmer wants to irrigate a piece of land in 15 hrs. The area of the field is 15 acres. the farmer grows alfalfa that requires 3.5 inches of water during the 15 hours.At what flow rate should the farmer pump the water

  Calculate the total axial deformation in the aluminum rods

A rigid rectangular shelf is suspended from a rigid ceiling by mean of four rods of diameter .505 inches. The two rods to the left L1 and L2, are made of steel. The two rods to the right R1 and R2 are made of aluminum.

  Maximum and minimum stress intensities in the section

Determine the maximum and minimum stress intensities in the section.

  What is the carbon concentration at 4 mm below surface

A 1045 steel will be heat treated in air at 900 C. What is the carbon concentration at 0.4 mm below the surface after 6 hours

  Determine what is the channel and flow classification

An obstruction is lodged in a 10-ft wide rectangular channel (n = 0.022) that has a botom slope of 0.005. The depth of the channel just upstream of the obstruction is 5.0 ft. If the flow rate is 325 cfs, what is the channel and flow classification

  Determine storage 1 hr later if average rates are given

The storage in a reach of river is 20,000 m^3 at a given time. Determine the storage 1 hr later if the average rates of in flow and out flow during the hour are 20 and 18 m^3/s, respectively

  Determine diameter of 200 m section commercial steel pipe

determine diameter of 200 m section commercial steel pipe (darcy's friction factor f = 0.0115) that carries a flow of 0.24 m^3/s and allowable head loss ove the section is 3.5 m.

  Determine what is the order and class of the leveling

Differntial Leveling between BM's A,B,C,D, and A gives elevation differences (in meters) of -15.632, 32.458, 38.214, and -55.025, and distances in km of 4.0, 6.0, 5.0, and 3.0 respectively.

  Is the flow laminar or turbulent and find reynolds number

For Oil (SG=0.86, u=0.025 Ns/m^2) flow of 0.3m^3/s through a round pipe with diameter of 500 mm, determine the Reynolds number. Is the flow laminar or turbulent

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd