Estimate the ground level so2 at a point of the power plant

Assignment Help Civil Engineering
Reference no: EM13310811

A power plant emits 95 g/s of SO2 from an effective stack height of 60 m. The wind speed is 3 m/s and the solar insolation is slight.

A) Estimate the ground level SO2 (ug/m^3) at a point 4 km directly downwind of the power plant

B) Estimate the ground level SO2 (ug/m^3) at a point 2 km downwind and 0.6 km off the axis

C) If the temp is 10 C and the pressure is at 1 atm, does the air quality of A and B meet the NAAQS requirement of 0.14 ppm?

Reference no: EM13310811

Questions Cloud

Describe how one of these solutions operates and : Describe, using diagrams where appropriate, the market for rental accommodation before and after the introduction of rent controls. Illustrate the surpluses accumulating to producers and consumers before and after the introduction of the price ceilin..
Determine the resulting velocity of center of the cylinder : a 9in radius cylinder of weight 18lb rests on a 6lb carriage. the system is at rest when a force p of magnitude 2.5 lb is applied ( p is coming out of the car the cylinder is sitting on and going to the right) for 1.2s.
What is the speed of the wrench when it hits the ground : A worker on top of a radar tower 22.4 ft high drops a wrench off the tower. What is the speed of the wrench when it hits the ground
What is the speed of the arrow : A soldier has a huge contraption that notches a large 4 kg arrow (it looks more like a lance) in a massive bow and uses a winch system to draw the arrow back to set the bow. What is the speed of the arrow
Estimate the ground level so2 at a point of the power plant : A power plant emits 95 g/s of SO2 from an effective stack height of 60 m. The wind speed is 3 m/s and the solar insolation is slight. A) Estimate the ground level SO2 (ug/m^3) at a point 4 km directly downwind of the power plant
What is the speed of the cart before collision : A 202 kg cart runs into the rear end of a 103 kg cart that is stationary. what is the speed of the cart before collision
Evaluation will be based on insights demonstrated : Evaluation will be based on insights demonstrated, evidence of critical thinking, and competent writing skills.
What is the distance uncertainty at the surface of ellipsoid : if a hand-held GPS unit locates a latitudinal position with an uncertainty of + - 0.02-seconds, what is the distance uncertainty at the surface of the ellipsoid.
Find energy stored in the capacitor after glass is removed : A parallel plate capacitor of capacitance 4.1 uF has the space between the plates filled with a slab of glass with k = 2.9, Find the energy stored in the capacitor after the glass is removed

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the normal and shear stresses

The grains of wood in the board make an angle of 20 degrees with the horizontal as shown. Determine the normal and shear stresses that act perpendicular and parallel to the grains if the board is subjected to an axial load of 250 N.(Dimensions l=3..

  Sketch and label vi-vo and vn versus time

An inverting amplifier is implemented with a R1=10 kilo Ohms and R2= 100 Kilo Ohms, and an op amp with finite open-loop gain a=10^3 V/V. Sketch and Label Vi,Vo,and Vn versus time if Vi is a 1-kHz triangular wave

  Calculate the initial head loss through a dual-media filter

The porosity of both media is 0.40, the shape factor for the anthracite is 7.5, and the shape factor for the sand is 6.0. Assume a water temperature of 60 F.

  What distance must be cleared from the inside edge

design a horizontal curve with a 40-degree central angle ( delta = 40) for a two-lane road with 11-ft lanes. The design speed is 70 mi/h and superelevation is limited to 0.06 ft/ft. Give the radius, degree of curvature, and length of curve that yo..

  What fraction of the herbicide is adsorbed

The herbicide 2,4,D, is applied to a golf course at a rate of 1.2 kg/ha. The organic matter content of the soil is 1%, bulk density is 1.3 g/cm3, and water content is 0.3.

  What is the max tensile force that could be applied to steel

a rectangular piece of steel is 10" wide by 60" long by 3" deep, what is the max tensile force that could be applied to the steel, and what is the total elongation of the steel

  What is the theoretical rate of moisture removal from grain

A model grain dryer is being used to investigate the drying process. It is discovered that the load cell which supports the dryer indicates that the mass of the dryer and its contentsinitially increases during the heat-up.

  Design a circular radial-flow clarifier for a town

Design a circular radial-flow clarifier for a town with a projected population of 45,000. Assume that the wastewater flow is 400 L/capita-day. Size the system for a 2-hr detention time at average flow.

  What are the effects of water pollution on the components

What are the effects of water pollution on the components of the hydrologic cycle?

  Cause of heading-up of the water surface

A rectangular channel 2.0 m wide carrying a discharge of 2.5 m3/s is to be fitted with a weir at its downstream end to provide a means of flow measurement as well as to cause heading-up of the water surface.

  What concentration of ozone is sometime used as disinfectant

The 3.0-ft diameter piper is 3,400 feet long with a steady flow rate of 10,000 gal/minozone (in mg/L) should be Injected at the head of the piper so what there will be an ozone concentration of 1.0mg/L

  Describe the equation for discharging a water tank

Describe the equation for discharging a water tank. Use: H= 2m, A_s= 1m^2, density water= 1000kg/m^3, K = 1kg hr^-1 m^-1/2 Mass flow in = 0 and mass flow out given by, Mass flow out = K z^1/2.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd