Estimate the common logarithm of 10 using linear

Assignment Help Mechanical Engineering
Reference no: EM13630960

Estimate the common logarithm of 10 using linear interpolation.

a) interpolate between log(8)=0.9030900 and log(12)=1.0791812.

b) interpolate between log(9)=0.9542425 and log(11)=1.0413927.

For each of the interpolations, compute the percent relative error based on true value.

Reference no: EM13630960

Questions Cloud

The current it flowing in a rlc circuit with r11ohm l01h : the current it flowing in a rlc circuit with r11ohm l0.1h c10-2f and the source voltage et 110sin377t becomes steady
In an orthogonal cutting operation the chip velocity was : in an orthogonal cutting operation the chip velocity was determined using a laser doppler velocimeter ldv as 80 of the
A large stationary diesel engine produces 15mw with a : a large stationary diesel engine produces 15mw with a thermal efficiency of .4. the exhaust gas which we assume is are
The cable is made of steel what diameter should tar cable : the cable is made of steel. what diameter should tar cable b so that the material does not exceed 50 percent of its
Estimate the common logarithm of 10 using linear : estimate the common logarithm of 10 using linear interpolation.a interpolate between log80.9030900 and log121.0791812.b
Write the expression for the radial distribution function : write the expression for the radial distribution function of a 3p electron in a hydrogenic atom and determine the
The compressor uses 16 kw of power what is the maximum : a heat pump with refrigerant 134a is used maintain a house at 25 degc by absorbing heat from a geothermal water source
The magnetic field inside a superconducting solenoid is : the magnetic field inside a superconducting solenoid is 5.00 t. the solenoid has an inner diameter of 6.20 cm and a
An engineer needs to monitor a flow of 20degc gasoline at : an engineer needs to monitor a flow of 20degc gasoline at about 250plusmn25 galmin through a 4- in-diameter smooth

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Will this specimen experience fracture if the largest

a specimen of a 4340 steel alloy having a plane strain fracture toughness of 45 mpa m is exposed to a stress of 1000

  The angular acceleration is 05 rads2 counterclockwise find

the 60-kg uniform rectangular plate rotates in a vertical plane around point a. force p is being applied to point c on

  Using the routh-hurwitz criteria and the root locus method

the loop transfer function of a single-loop negative feedback system isls gcsgs ks 2.5.5 3.2 s2s 1s 10s 30this

  A projectile is fired at an angle of 62deg from the

a projectile is fired at an angle of 62deg from the horizontal with a velocity of 704 ftsec. if it lands 4.75 seconds

  Consider a supersonic wind tunnel with test section mach

consider a supersonic wind tunnel with test section mach number of 2 and fixed geometry diffuser designed to operate

  What is the flow rate of cell suspension from the membrane

a battery of cylindrical hollow-fiber membranes is operated at steady state to concentrate a bacterial suspension from

  You are manufacturing a frame for a vehicle out of some

you are manufacturing a frame for a vehicle out of some aluminum alloy 6061-t451 tubing. the frame is to be welded

  If a starts from rest at x0 and moves to the right with a

the rod ab slides through the pivoted collar as end a moves along the slot. if a starts from rest at x0 and moves to

  The spring has squared and ground ends and is made from

a helical compression spring is required to provide a minimum force of 80n at installation and have a working

  An electric motor of total weight 3330 pounds is mounted on

an electric motor of total weight 3330 pounds is mounted on a simply supported beam with an overhang as shown

  What is the temperature and pressure of the oxygen within

a piston with a mass of 500 kg is being held in place by 0.5 kg of oxygen in a circular cylinder of diameter of 50 cm.

  Calculate the velocity and acceleration of collar a

In the position shown, the angular velocity and the angular acceleration of the rod AB are 4 rad/sec and 6 rad/sec2, respectively, both counterclockwise. For this instant calculate the velocity and acceleration of collar A. ( AB = 600 mm)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd