Eliminate the undesired component by using band-pass filter

Assignment Help Electrical Engineering
Reference no: EM13279483

Write the code for an m-file (script) that will be used to generate a DSB signal, an AM signal derived from the DSB signal, and a down-converted AM signal. The specifications for the simulation are:

Modulating Frequency = 1kHz, Initial Center Frequency = 30kHz, Final Center Frequency = 20kHz, Time Vector:3001 points over range from 0 to 3 ms (3 cycles at the modulating frequency).

1. Generate a DSB signal based on the modulating frequency, the initial center frequency, and amplitudes of 1.

2. Add the carrier to the DSB signal and set the modulation to 75% for the AM signal.

3. Provide an ideal mixing operation with a 10-kHz local oscillator having an amplitude of 2, and eliminate the undesired component by using a band-pass filter centered at 20kHz. The bandwidth should be sufficient to pass the shifted AM signal. A reasonable choice would be to set 3-dB points at 18.5 and 21.5kHz.

Reference no: EM13279483

Questions Cloud

Design an n-channel silicon jfet with pinch off voltage : design an n-channel silicon JFET with pinch off voltage (-2V). The channel is doped with Arsenic and the gate is doped with Boron. the Boron density is 1019 atoms /cm-3 all atoms are fully ionized. The resistance of the channel at zero gate bias i..
Calculate the beta for the stock : Calculate the beta for the stock. Using Excel and the DATA worksheet, calculate the stock's beta by regressing the monthly stock returns on the market's monthly returns. The monthly Return =.96% and the market index level is 1,552.10
Explain chromatography in the presence of 6 m guanidine : Chromatography in the presence of 6 M guanidine hydrochloride yields only a peak for a protein of Mr 60,000. Chromatography in the presence of 6 M guanidine hydrochloride and 10mM 2-mercaptoethanol yields peaks of Mr 34000 and 26000
What is the risk structure of interest rates : What is the risk structure of interest rates? And, what are the three major components that are included.
Eliminate the undesired component by using band-pass filter : Provide an ideal mixing operation with a 10-kHz local oscillator having an amplitude of 2, and eliminate the undesired component by using a band-pass filter centered at 20kHz. The bandwidth should be sufficient to pass the shifted AM signal.
Define competed another marathon : To qualify to run in the 2005 Boston Marathon, a distance of 26.2 miles, an 18 year old woman had to have competed another marathon in 3 hours and 40 minutes or less. To qualify, what must a woman's average speed have been
What is the final angular speed of the monkeys head : A monkey shows symptoms of being under the influence of too much physics. Specifically, What is the final angular speed of the monkey's head
Compute maximum compression ratio expected in average text : If we were to use the same number of bits for all symbols in this set, how many would we need for each symbol. In the parts below, assume we are using a compression method that takes advantage of the relative frequency of each symbol.
Explain how to calculate the dh for the reaction : The "roasting" of 48.7 g of ZnS at constant pressure gives off 220. kJ of heat. Calculate the DH for this reaction. 2ZnS(s) + 3O2(g) ® 2ZnO(s) + 2SO2(g)

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the armature voltage to be applied in steady state

Plot the steady state torque-speed characteristic for Va = 100V, 60V, and 30V. Calculate the armature voltage to be applied in the steady state at the speed of 1500 rpm when the motor torque load require is 3 Nm.

  Design using the bilinear z-transform design method

Design lowpass IIR filter with the following specifications: Filter order = 2, Butterworth type Cut-off frequency=800 Hz Sampling rate =8000 Hz Design using the bilinear z-transform design method

  Show design procedure circuit

Design a m-seguence PN generator using 3 shift registers. Show design procedure circuit and PN sequence and find 16 Walsh codes for modulating (encoding) a 4-bit data packet

  Compute the speedup and efficiency

computation with 5% of the code that cannot be paralleled, compute the speedup and efficiency.

  At most how many 1-operand instructions can be formulated

A computer has 16-bit instructions and 64 registers. Suppose it is required to have at least 14 instructions designed to have 2 operands from registers (e.g., add, $1, $3 puts the sum of $1 and $3 into $1.

  How to check if the bulb is bad and needs replacing

An incandescent light bulb can be modeled as a resistor with a value of a few ohms. Imagine an incandescent light bulb goes out in your house. Using your trusty multimeter, how would you check if the bulb is bad and needs replacing

  How to build each single-or multiple-output logic functions

Show how to build each of the following single- or multiple-output logic functions using one or more 74X138 or 74X139 binary decoders and NAND gates. (hint: Each realization should be equivalent to a sum of minterms)

  Angle modulation and detection

State Carson's rule for bandwidth estimation. What does it reduce to for NBFM and WBFM and d erive an time domain expressionfor the output xd(t) of the system

  Determine the probability mass function-pmf

encounter a sequence of birds while walking in the park. The birds can either be blue (B) or red (R). We let X be the random variable corresponding to the number of birds we encounter until seeing the first blue one.

  How many ways are there to draw 3 resistors from a box

Calculate the probability of drawing 3 10 k resistors from a box of 500 resistors, where 495 are 100 k resistors and 5 are 10 k . Use your results from part (a) and (e) to find this probability. How many ways are there to draw 3 resistors from a bo..

  How much coal must be burned to produce amnt of electricity

From your group, pick 3 mobile phones, and/or portable devices that are rechargeable. Estimate (using resources and available data), how much electricity that is used to charge them on a weekly basis

  Determine relation between acceleration and output voltage

An LVDT is used in an accelerometer to measure seismic-mass displacement. The LvDT and signal-conditioning output is 0.31 mV/mm with a +/-2 cm maximum core displacement. The spring constant is 240 N/m, and the core mass is 0.05 kg.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd