Dry air is contained in a tank with fixed volume

Assignment Help Mechanical Engineering
Reference no: EM13713177

Dry air is contained in a tank with fixed volume at 200 degrees Celsius and a pressure of 5 bar. Then the fluid is heated so that its temperature reaches up to 300 degrees Celsius. If the volume of the tank is 0.2 m^3, find the transferred heat and final pressure and the change in entropy.

Reference no: EM13713177

Questions Cloud

What is the angular acceleration of the drive : a hard drive is turned on from rest and accelerates to 5100rpm rpm in 5.14 s. The drive then maintains this rate of rotation for 164s at which point it is turned off and slows to a stop.
Estimate minimum fluidizing velocity for air and for water : For spherical sand particles with Dp = 0.045 inches and the density of each particle is 145 lbm/ft3, estimate the minimum fluidizing velocity for air and for water. Assume a porosity of 32 percent. You may need to rederive Equation 11.41 considering ..
Find the position of the center of mass of the system : Find the position of the center of mass of the system of the sun and Jupiter. Since Jupiter is more massive than the rest of the planets combined.
Find the velocity of the wreckage just after impact : a 1015-kg compact car is traveling north at 15 m/s when it collides with a 2102-kg truck traveling east at 10 m/s. The insurance adjuster has asked you to find the velocity of the wreckage just after impact. What do you tell him.
Dry air is contained in a tank with fixed volume : Dry air is contained in a tank with fixed volume at 200 degrees Celsius and a pressure of 5 bar. Then the fluid is heated so that its temperature reaches up to 300 degrees Celsius. If the volume of the tank is 0.2 m^3, find the transferred heat and f..
Internal pressure onset of yielding based on tresca criteria : A thin-walled cylinder with open ends is subjected to constant torque of 150,000 lb-in. The cylinder is made of 2024-T3 Aluminium with a yield strength Y=50 ksi. The cylinder has a mean radius r=5in and a wall thickness of 0.05inches.
What is the length of a : Consider A= 3i+j+2k. What is the length of A, Find the unit vector of A' in the same direction as A. What is the angle between angle A and the y-axis.
What is the lasting value of big international conferences : What is the lasting value of big international conferences on sustainable development and how likely do you think it is that sustainability can be achieved solely by individuals without systemic change?
Determine the minimum diameter of the pipe : Gasoline (density = 680 kg/m^3 and kinematic viscosity = 4.29x10^-7 m^2/s) is transported at a rate of 150 L/s for a distance of 2 km. The surface roughness of the piping is 0.03 mm. If the head loss due to pipe friction is not to exceed 10 m, determ..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  A motor car shaft consist of a steel tube 30 mm internal

a motor car shaft consist of a steel tube 30 mm internal diameter and 4 mm thick .thee engine develops 10kw at

  The asymmetric simple truss is loaded as shown

The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the weight of the structure compared with the applied loads. Is the knowledge of the size of the structure necessary?

  Determine the new volume of the gas

0.112m^3 of gas has a pressure of 138kN/m^2. It is compressed to 690kN/m^2 according to the law PV^1.4 = C. Determine the new volume of the gas.

  Oil a has a viscosity of 80cst at 40c and 8cst at 100c oil

two oils are tested to establish their viscosity index. oil a and oil b have their viscosity measured at temperatures

  Determine the specific volume of the saturated vapor at the

a rigid tank contains a two-phase mixture consisting of 0.2 lb of liquid water and 0.1 lb of water vapor initially at a

  The maximum height h of the loop is the same as the initial

block a is released from rest and slides down the frictionless ramp to the loop. the maximum height h of the loop is

  Water in a piston-cylinder assembly with an initial volume

water in a piston-cylinder assembly with an initial volume of 0.01m3 has an initial temperature of 120c and an initial

  A paddle wheel stirs up the water expending 40 kj of work

a 2 kg container of water is at 20 degrees c and is in a room having a temp of 10 degrees c. a paddle wheel stirs up

  Design a chain drive for this uniformly loaded system

a system has an input speed of 900 rpm and a desired output speed of 230-240rpm. the system is to transmit 15.0hp.

  The convection coefficient is 55 wm2 k and radiation

a steam pipe of 120 mm outside diameter and is covered with a 20 mm thick layer of calcium silicate insulation k

  One leg of the manometer is open to the atmosphere p101325

a tank contains a gas at an absolute pressure of 104.0 kpa. the pressure in the tank is measured using a mercury p13.59

  What type of feedback data should we be collecting

what type of feedback data should we be collecting; in order to make sure that our MPS data, our MRP data, our Aggregate Planning, etc. are all correct?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd