Draw the shear force and bending moment diagrams

Assignment Help Mechanical Engineering
Reference no: EM131370313

Computer Aided Engineering Final Exam

Q1. Figure shows a concrete reinforced slab undergoing deflection under its own weight. Using the FEM principles (stiffness method), calculate

a. Deflection and reactions at the nodes (define the nodes as required).

b. Draw the shear force and bending moment diagrams (using FEM).

c. Compare the maximum deflection using FEM with analytical results.

Modulus of elasticity = 5.0 × 106 psi

Weight per cubic feet of slab = 150 lb

Assume width in the perpendicular direction (z-dir) = 1 in

1067_Fig..png

Q2.  Many flow problems can be simplified and modeled as flow between two infinite parallel plates e.g.  lubrication leakages in  hydrostatic bearings. The flow between the plates is given by the following equation:

μ(d2u/dx2) = dp/dx

u is the fluid velocity between the plates, µ is the dynamic fluid viscosity, and dp/dx is the constant pressure drop. 

1900_Fig1.png

a. Using Galerkin's method, obtain the equation for velocity profile. Assume displacement function to be 

u- = C1[sin(πy/H)]

b. Find the exact solution for the velocity profile.

c. Solve the velocity profile using finite difference approach. 

d. Compare the results of all of the above approaches using the following values µ = 0.05 N.s/m, H = 0.02 mm, dp/dx = -200 MPa/m. Use an excel sheet to plot the velocity profiles.

e. How do the maximum velocities compare for each case?

Q3. A variable cross-section plate is shown in the figure. The plate supports a load of 2500 lb.

1165_Fig2.png

a. Using direct stiffness method (one dimensional method), determine the deflection of the plate at nodes 2, 3 and 4. The modulus of elasticity of the material is 20e3 ksi.

b. Also calculate the stress in all the three elements.

Q4. You have already submitted the MATLAB code to calculate the reactions and deflections in 3D truss. I asked you to update the code to calculate strains and stresses too. Submit the updated code.

Reference no: EM131370313

Questions Cloud

Explain how often a resume and cv should be updated : Identify the primary type of resume and/or CV you expect to use in your job search and career progression. Explain how often a resume and/or CV should be updated (support your answer).
Write a thesis statement at the end of your introduction : Firstly, I notice that your essay does not effectively summarize an ethical position. In your draft, what you did is simply explain what the president should do about the global warming and climate change problem. There are no details to explain w..
Prepare cv for a job : Prepare C.V. for a job by considering the given information.
What is the importance of each of the six topics : What is the importance of each of the six topics within your company? What is the usefulness of understanding this topic in today's corporate structure? How does managerial economics fit into your topic?
Draw the shear force and bending moment diagrams : MECT 6322 - Computer Aided Engineering Final Exam. Figure shows a concrete reinforced slab undergoing deflection under its own weight. Using the FEM principles (stiffness method), calculate- Deflection and reactions at the nodes (define the nodes as..
What practical steps could be taken to build a relationship : What practical steps could be taken to build a relationship with a follower of this worldview who might be a co-worker, neighbor, etc.?
Would a batch input system offer any advantages : Suggest at least three specific data validation checks that might help reduce input errors.
Find the most economic batch quantity : Find the most economic batch quantity of a product on a machine if the production rate of that item on the machine is 200 pieces per day and the demand is uniform at the rate of 100 pieces per day. The ordering cost is Rs. 200 per batch and the co..
How frequently should production run be made : The cost of holding a bearing in stock for one year is Rs.2 and the set-up cost of a production run is Rs.1,800. How frequently should production run be made?

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  What is the temperature of the system

If level k is 3 × 10-6 eV above level j, what is the ratio of the number of molecules in level k and the number in level i?

  Compare the thermal efficiency of a two-stage gas turbine

compare the thermal efficiency of a two-stage gas turbine with regeneration reheating and intercooling to that of a

  On what basis should the decision be made

What are the relevant costs to be considered when deciding whether to take a quantity discount? On what basis should the decision be made?

  Is it possible for one object to gain mechanical energy

Is it possible for one object to gain mechanical energy from another without touching it?

  Find the elevation of the pump relative to the reservoir

A fire truck draws water from an open constant-level reservoir through a hose of 0.2 ft2 cross section. The water is discharged from the pump through another 0.2 ft2 hose to a surge tank pressurized to 120 psig with air at the top. The pump adds 970 ..

  How long would it take to fill up

If the town of Chapel Hill used the Smith Center as a refuse disposal site, how long would it take to fill up? Make all necessary assumptions.

  1-2 an actual refrigerator absorbs 500 kj of heat from a

1-2 an actual refrigerator absorbs 500 kj of heat from a sink at 250 k and reject 660 kj of heat to environment at 300

  Assuming constant specific heats for air at room

a well insulated 4-m x 4-m x 5-m room initially at 10 c is heated by the radiator of a steam heating system. the

  At the beach atmospheric pressure is 1025 mbar you dive 15

at the beach atmospheric pressure is 1025 mbar. you dive 15 m down in the ocean and you later climb a hill up to 250 m

  Discuss the applicability of the final-value theorem

If, prior to closing the switch, the currents in both circuits are zero, determine the induced current i2(t) in the secondary circuit at time t when R1 = 4 Ω, R2 = 10 Ω, L1 = 2 H, L2 = 8 H, M = 2 H and e(t) = 28 sin 2t V.

  A plane wall 15 cm thick has a thermal conductivity given

a plane wall 15 cm thick has a thermal conductivity given by the relation k 2.0 0.0005t wmk. where t is in kelvin.

  Balanced-cross-flow compact heat exchanger

A balanced-cross-flow compact heat exchanger is required for an air heating system that processes 0.5 kg/s air. The inlet temperature for the hot water is 295 K, and the cold air enters at 270 K to be heated to 287 K. The inlet pressure for the hot w..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd