Draw the proper orthographic views for the chuck jaw

Assignment Help Mechanical Engineering
Reference no: EM131439693

Assignment

Draw the proper orthographic views for the Chuck Jaw shown below. Dimension all views appropriately. Insert your B-size template and change the date, scale and assignment number in the title block as necessary. Make sure you have the following settings.

Layer

Line Type

Color

0

continuous

white

hidden

hidden or hidden2

red

center

center or center2

blue

dimension

continuous

magenta

section

continuous

cyan

phantom

phantom

green

Plot your views on a B (1 lx17)-size paper. Use the SAVEAS command and save your drawing to your folder and an USB disk. Turn in a hard copy (plot) of your drawing.

352_Chuck Jaw.jpg

Reference no: EM131439693

Questions Cloud

Market failure in addressing negative externalities : How do externalities positive or negative play a role regarding the demand and supply of a good or a service and what can government do to promote greater social welfare and reduce market failure in addressing negative externalities?
Develop beachfront property : Continue to suppose the developer's right to develop his beachfront property is protected by a property rule.  However, assume now that it costs the three residents a total of $10,000 to organize and act collectively.  Will the land be developed? ..
Write a documentary view about healthy science : Watch movie: fed up.Write a documentary view for 1-2 pages, about healthy science.
Structure sequential interview : Why would it be relevant for a company to interview for Human resources Director in a structure sequential interview ? Why would it be relevant for a company to use job related interview method to interview for the position of Book keeping ? Discuss ..
Draw the proper orthographic views for the chuck jaw : Draw the proper orthographic views for the Chuck Jaw shown below. Dimension all views appropriately. Insert your B-size template and change the date, scale and assignment number in the title block as necessary.
Plot PR PGov and f vs time : This system is producing 70 GW of power when load is suddenly increased to 73 GW. Plot PR, PGov. and f vs. time for 50 seconds after the change. I would need mfile and graphs must be oscilates
Identifying initiatives for practice change : Read: Prior to beginning this discussion, read Chapter 1 and Chapter 3 of your textbook along with the article "Physical health inequities in people with people with severe mental illness: Identifying initiatives for practice change."
Provides two types of rooms with three rental classes : Round Tree Manor is a hotel that provides two types of rooms with three rental classes: Super Saver, Deluxe, and Business. The profit per night for each type of room and rental class is as follows: Rental Class Super Saver Deluxe Business Room Type I..
Social media site to share and consume online information : Does your organization currently use any social media site to share and consume online information? What could be potential benefits of identifying social media content around a specific geographic location for your organization?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the overall efficiency the heat rate mw and the

calculate the overall efficiency the heat rate mw and the total fuel rate kgs of a combined-cycle power plant 1 if no

  What is the order of the system

What is the system matrix and what is the input distribution matrix for your choice of state variables?

  An electric field is e400nci for xgt0 and e-400nci for xlt0

an electric field is e400nci for xgt0 and e-400nci for xlt0. a cylinder of length 30cm and radius 10cm has its center

  Find the shear force vb and bending moment mb at point b

Find the shear force VB and bending moment MB at point B.

  Determine the thickness of the bar

A flat bar as shown in the figure below is subjected to an axial load F equal to 500 kn. Assuming that the stress in the bar is limited to 200 n/mm^2 determine the thickness of the bar. All dimensions are in mm

  Determine the head loss per unit length of this flow

Water flows through a 6-in.-diameter horizontal pipe at a rate of 2.0 cfs and a pressure drop of 4.2 psi per 100 ft of pipe. Determine the friction factor

  Determine the individual pressure drops to the nearest tenth

Determine the individual pressure drops to the nearest tenth (0.1) psi and the gage pressures to the nearest whole (1) psi

  Determine the smallest force p

For any possible position of the handle, determine the smallest force P and the corresponding value of a that will cause the press to tip about point A.

  Design a private sewage system

Design a private sewage system (seepage pits) for the apartment building in Appendix B. In this design, use a percolation rate of 16 min. Assume the maximum water table elevation is 2 ft (0.6 m) below grade.

  Calculate the plastic modulus z and the shape factor f

Calculate the plastic modulus Z and the shape factor f.

  Compute the velocity at point a when it reaches a treat the

the wheel consists of a 4-kg rim of 250-mm radius with hub and spokes of negligible mass. the wheel is mounted on the

  A rigid closed tank of volume 3 m3 contains 5 kg of wet

a rigid closed tank of volume 3 m3 contains 5 kg of wet steam at a pressure of 200 kpa. the tank is heated until the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd