Draw the pressure vessel large enough to show orientation

Assignment Help Mechanical Engineering
Reference no: EM13703059

A cylindrical pressure vessel of 120 in diameter outside, used for processing rubber, is 36 ft. long. If the cylinder portion of the vessel operates at 120 psi internal pressure, what are the stresses acting on an element at the inside surface of the pressure vessel. Draw the pressure vessel large enough to show the orientation of your selected stress element with the stresses acting on it.

Reference no: EM13703059

Questions Cloud

Natural gas having a molar analysis : Natural gas having a molar analysis of 60% methane (CH4) and 40% ethane (C2H6) enters a compressor at 340K, 6 bar and is compressed isothermally without internal irreversibilities to 20 bar. The compressor operates at steady state, the kinetic and po..
Dispute resolution : A group of neighbours in your area are fed up with a house of uni students who continue to have late night parties, disrupting the neighbourhood. You and your neighbours want to take action.
A cylindrical pressure vessel : A cylindrical pressure vessel of 120 in diameter outside, used for processing rubber, is 36 ft. long. If the cylinder portion of the vessel operates at 120 psi internal pressure, what are the stresses acting on an element at the inside surface of the..
Determine the increase in internal energy : Determine the increase in internal energy of 2 kg of argon if its temperature increases from 30C to 130C
Draw the pressure vessel large enough to show orientation : A cylindrical pressure vessel of 120 in diameter outside, used for processing rubber, is 36 ft. long. If the cylinder portion of the vessel operates at 120 psi internal pressure, what are the stresses acting on an element at the inside surface of the..
Inner surface of a horizontal cylindrical duct : Electronic components are mounted on the inner surface of a horizontal cylindrical duct whose inner diameter is 0.2 m, as shown in Fig. P6.96. To prevent overheating of the electronics, the cylinder is cooled by a stream of air flowing through it and..
Element at the inside surface of the pressure vessel : A cylindrical pressure vessel of 120 in diameter outside, used for processing rubber, is 36 ft. long. If the cylinder portion of the vessel operates at 120 psi internal pressure, what are the stresses acting on an element at the inside surface of the..
Determine the moment around the front axel m-while thrusting : The rocket car below is thrusting so that at constant thrust (force) , it reaches a velocity of 500 km/hr in 30 seconds. How much thrust is this (kN)? Determine the moment around the front axel M, while thrusting.
Find the tension in the towrope at this speed : An accelerating car develops 15 kW at a speed of 30 km/h on a level roadway, when towing an identical vehicle whose engine is out of action. Find the tension in the towrope at this speed, if each car has a constant attractive resistance of 650 N

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the rate of heat loss from the steam pipe

Taking the temperature of the surrounding surfaces to be 20°C also, determine the rate of heat loss from the steam pipe.

  A rigid vellel with the volume of 10 m3 contains a

a rigid vellel with the volume of 10 m3 contains a water-vapor mixture at 400 kpa at 60 percent quality. the pressure

  Find the angular frequency rads identify the total mass

a car with a mass of 1480 kg is constructed so that its frame is supported by four springs. each spring has a force

  Suppose that you can change the direction of f while

the force f 30i 20j - 10k n. a determine the magnitude of the moment of f about a. b suppose that you can change the

  How long does this coal reserve of us will last if all coal

name three countries with the largest percentage of the world coal proved reserve. using the latest value of us coal

  The temperature t is constant derive an expression using

a hollow vertical cylinder with rigid walls and a height of h is closed on both ends and is filled with an

  A mining engineer plans to do hydraulic mining with a

a mining engineer plans to do hydraulic mining with a high-speedjet of water. a lake is located h300 m above the mine

  Consider two identical rooms one room has a refrigerator in

consider two identical rooms one room has a refrigerator in it the other does not. all the doors and windows in each

  The speed limit on a country road is 70 kmhr the radius of

the speed limit on a country road is 70 kmhr. the radius of curvature for a bridge on the road is 50 meters. a corvette

  Suppose an external torque t1 is applied to shaft 1 which

suppose an external torque t1 is applied to shaft 1 which has polar area moment of inertia j1. gear 1 is mounted on

  The temperature stays constant at 290 k for the air

a rigid tank initially contains 3 kg of air at 500 kpa 290 k. the tank is connected by a valve to a piston-cylinder

  Which of these two processes will produce the largest amount

which of these two processes will produce the largest amount of work? (You must provide a full explanation for your choice).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd