Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
implement a circuit that allows counting the number of persons entering exposure. The exhibition hall can accommodate 7 people. Has a uniqueinput and a single output.At the entrance is placed a sensor such that when a person enters the room sensor sends a positive pulse and the output has placed a similar sensor.You will be asked to design the logic circuit such that a 7-segment display can be know the number of people who are in the room.Note: never going to be the case that a person joins the room at the same time another person leaves.Is asked to:
a) Truth table of the circuit.b) Draw a diagram of logic design implemented with JK-FF.c) Draw the state diagram.d) Explain in detail the operation of the circuit.
Which of these metrics are dependent on link conditions: CINR, SNR, or BER Evaluate the pros and cons of using the SNR and signal - to - interference - noise ratio ( SINR ) for estimating signal quality versus using the absolute value of the signa..
The terminals of an electrical device are labeled a and b. If vab = 10V , how much energy is exchanged when a charge of 3 C moves through the device from a to b. Is the energy delivered to the device (i.e., device dissipating or storing energy).
Use the Timeout class to provide a two second delay. During the delay, display the number of interrupts that are occurring on Pin 5 using LED1-LED4. LED1 is the low-order bit. Use only the BusOut class for driving the LEDs.
Due to an Internet configuration error, packets sent from New York to Los Angeles are routed through El Paso, Texas with probability 3/4. Given that a packet is routed through El Paso, suppose it has conditional probability 1/3 of being dropped.
A 120 Veff motor draws 1.5 kVA at a lagging power factor of .85. Determine the size of the capacitor that must be placed in parallel with the motor for a power factor of 1.
Suppose that a current x(t) = e^-0.5t for t > or equal to 0, and zero otherwise is applied to a discharged capacitor of capacitance C =1F at t = 0 sec. What would be the voltage in the capacitor at t= 1 seconds
a. A load consumes 150kW with a power factor pf = 0.7 (lagging). If the load current is 240A (RMS), find the load voltage. b. An industrial plant has an inductive load which consumes 10kW of power from a 220VRMS line.
Question about Subnets, An organization owns the network 200.1.1.0/24 and wants to form subnets for 4 departments, with hosts as follows
In multiplicative decrease, the congestion window size decreases by half(if the result is not an integer round down to the nearest integer).Suppose that the two TCP connections C1 and C2, share a single congested link of speed 30 segments per seco..
A silicon p-n-p transistor has impurity concentrations of 5*10^18, 2*10^17, and 10^16 cm^-3 in the emitter, base, and collector, respectively. The base width is 1.0 um and the device cross-section area is 0.2 mm^2.
Determine the energy or the power in the signal. x(t) = e-a*abs(t) where a > 0 and abs(t) means the absolute value of t.
Recall that the median is the value in an ordered list of values above and below which there is an equal number of values. The median filter is often employed when one wishes to remove zero-mean additive noise while preserving sharp edges in the o..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd