Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Create a fictional start- up company that serves the U.s. market with a product or service. Develop a marketing plan for your business this should include an introductory statement to describe your product /service A description of your target market. Information about your distribution, pricing and promotional strategies
The conductor, its motion, and is the required length of the conductor? It turns out that in generator design, a conductor of this length is impractical, and we must use N conductors of length 0.1 m. However, by connecting the conductors in series..
Find the values of I and V for the circuits assuming diode are ideal. Consider Vin=0,2,6, and 10V. Also plot V vs. Vin for Vin ranging from -10V to +10V
The rotor of a 4 pole generator is wound with a 100 turn coil. If the flux per pole is 4.5mWb and the rotor turns at a speed of 1800 rpm, determine (a) The frequency of the induced voltage in the rotor.
A 3.0 μF capacitor is charged to 40 V and a 5.0 μF capacitor charged to 18 V are connected to each other, with the positive plate of each connected to the negative plate of the other. What is the final charge on the 3.0 μF capacitor
Consider a plane wave normally incident on a half-space of copper. If f=1GHz, compute the propagation constant, intrinsic impedance, and skin depth for the conductor. Also compute the reflection and transmission coefficients
Design a PD Controller G_c(s) = K_p + K_d*s using the root-locus method such that the closed-loop system has a damping ratio, zeta = 0.7 and a natural frequency, omega_n = 0.5 rad/sec.
A 20-Hp, 240VDC, 4-pole Shunt motor operates at rated load and 1700rpm and an efficiency of 88%. It has armature resistance of 0.2Ω and field resistance of 240Ω. Find: a)Power input to the motor b)IFLA of the motor
A square metal plate is heated to 80 degrees celsius at the corner corresponding to x = y = 1. The temperature distribution in the plate is described by T = 80e^(-(x-1)^2)*e^(-3(y-1)^2) Obtain the surface and contour plots for the temperature.
The rate of heat loss from the air in the duct is estimated to be 300 W. Determine the power rating of the electric resistance heating element.
A Si is doped with 10^14 boron atoms per cm3. For T=300 K and T = 470 K. Determine the position of Ei, compute Ef-Ei, and draw a careful dimensioned energy band diagram for the Si sample. Note for Si Eg=1.1 eV, mp*/mn*=0.71. ni=10^14 cm-3 at 470 K
A diode is connected in series with a 30-V rms source to charge a 12-V battery with an internal resistance of 0.1 ohm. Specify the series resistance necessary to limit the peak current to 2A. Estimate the time required to recharge a 10-A hr batter..
Derive a state table for the FSM that produces z=1 when it detects that either the sequence w:0010 or w:1110 has been applied; otherwise, z=0. After the fourth clock pulse, the machine has to be again in the reset state, ready for the next sequenc..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd