Discuss the power lost in the hydraulic jump

Assignment Help Mechanical Engineering
Reference no: EM131260702

Water is flowing as shown in Fig. P10.40 under the sluice gate in a horizontal rectangular channel that is 5 m wide. The depths y1 and y2 are 2.5 m and 10 cm, respectively. The horizontal distances between locations 1, 2, and 3 are sufficiently short that rapidly varied flow conditions can be assumed to occur. Determine the following:

(a) The discharge

(b) The depth downstream of the jump at location 3

(c) The power lost in the hydraulic jump

1029_501e9051-83d5-414d-8204-ce15058ff3be.png

Reference no: EM131260702

Questions Cloud

Implementation of community health information network : 1a. From the e-Activity, determine a key trend that supports the implementation of either a community health information network (CHIN) or regional health information organizations (RHINO) in today%u2019s health care organizations. Justify your re..
Determine the most profitable number of each model : Alpha 1s generate a $1,200 profit per unit, and Beta 2s yield $1,800 each. Determine the most profitable number of each model of robot to produce during the coming month.
Alternative methods of dispute resolution : 1. Describe the steps involved in civil litigation, beginning at the point where a dispute arises between the parties, and ending at the point where the jury returns a verdict. Include in your description the pretrial stages of a civil lawsuit, a..
Discusses threats that stgs pose to correctional agencies : Compose an essay of 500 - 700 words that discusses the threats that STGs pose to correctional agencies. As part of your response, discuss measures that correctional agencies can take to control the influence of STGs within an incarceration facilit..
Discuss the power lost in the hydraulic jump : Water is flowing as shown in Fig. P10.40 under the sluice gate in a horizontal rectangular channel that is 5 m wide. The depths y1 and y2 are 2.5 m and 10 cm, respectively.
Define the objective function and constraint equations : Define the objective function and constraint equations. - Graph the feasible region.  -  What is a maximum-profit daily production plan at the new factory?
What did having a key informant add to your understanding : What event/activity did you observe and how/why was it a new experience for you? What understanding was gained from participation compared to just observing? What did having a key informant add to your understanding?
Can any aspect of the scenario be classified as hearsay : Can any aspect of the scenario be classified as hearsay - Do any hearsay exemptions or exceptions apply and did the suspect provide a confession - Was the Miranda rule correctly applied and Are there any exceptions to the Miranda warning requirement ..
Find by graphical linear programming the best production mix : Each model B gate requires 100 lb of steel and 30 lb of zinc and can be sold for a profit of $70. Find by graphical linear programming the best production mix of yard gates.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The water enters the electric heater at 60f and is heated

a household hot water system heats water only as it is needed. the water enters the electric heater at 60f and is

  Fraction of the block volume

A cubical block of density PB and with sides of length L floats in a liquid of greater density PL (a) What fraction of the block's volume is above the surface of the liquid?

  Estimate the cutting time for the cut

In cutting a 6-in.-long slot in a piece of AISI 1020 cold-rolled steel that is 1 in. thick, the material is fed to a band saw blade with teeth having a pitch of 1.27 mm (20 pitch) at the rate of 0.0001 in. per tooth. Estimate the cutting time for ..

  Determine the deflection of the spring

A close coiled helical spring of round steel wire 10mm diameter having 10 complete turns with a mean radius of 60mm is subjected to an axial load of 200 N. Determine the deflection of the spring.

  Determine the specific volume of the rock

A rock weighs 90.8 N in air and 45 N when completely submerged in water. Determine the specific volume of the rock in m3/kg

  The low-temperature reservoir of a carnot heat engine is

the low-temperature reservoir of a carnot heat engine is at 10 c. to increase the efficiency of this heat engine from

  A jet is traveling westward with the sun directly overhead

a jet is traveling westward with the sun directly overhead the jet is on a line between the sun and the center of the

  Determine a the distance l required for the droplets to

in space a novel heat rejection scheme that has been proposed for heat dissipation is termed a liquid droplet radiator

  A flange is used for instrument connection for a system

a flange is used for instrument connection for a system with a design temperature of 316degc 600degf and a design

  Determine the plastic moment mp for a beam

Determine the plastic moment MP for a beam having the cross section shown in the figure if σY= 210 MPa.

  What is number of rps at wich this rod ruptures

A horizontally oriented copper rod length of l=1m is rotated about avertical axis passing through its middle. what is number of rps at wich this rod ruptures?

  Size of the component ions

1. In ionic materials, how does the size of the component ions affect the extent of elec- tronic polarization? 2. Can a material have an index of refraction less than unity? Why or why not?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd