Difference between sensor less ECS and sensor end ECS

Assignment Help Mechanical Engineering
Reference no: EM13718427

What is the difference between sensor less ECS and sensor end ECS. Can a motor with a sensor less ECS be programmed into a controller and be programmed autonomously?

Reference no: EM13718427

Questions Cloud

Products of the flash system are fed to distillation column : We are separating ethanol and water. All percentages are mol%. Find the q values and plot the feed lines. a) Feed is 60% ethanol and flashes in the column with v/f=0.37 b)Feed is 40% ethanol and is a two-phase mixture with liquid and vapor in equilib..
Entropy generation during the compression of steam : Determine the work input and entropy generation during the compression of steam from 100 kPa to 5 MPa in (a) an adiabatic pump and (b) an adiabatic compressor is the inlet state is saturated liquid in the pump and saturated vapor in the compressor an..
Develop marketing plan for product or service of your choice : Develop a marketing plan for a product or service of your choice offered in the Northern Territory.
Assume the supports only exert vertical forces on the pipe : The open-ended polyvinyl chloride pipe has an inner diameter of 4 in. and thickness of 0.2 in. It carries flowing water at 57psi pressure. If the flow of water within the pipe is stopped due to the closing of a valve, determine the state of stress in..
Difference between sensor less ECS and sensor end ECS : What is the difference between sensor less ECS and sensor end ECS. Can a motor with a sensor less ECS be programmed into a controller and be programmed autonomously?
Estimate the wind velocity during a hurricane : A drag force meter is used to estimate the wind velocity during a hurricane. A force of 4.8 N is measured by the meter and the meter has a cross sectional area of 16.9 cm2 with a coefficient of drag of 0.66. What is the wind velocity in mph? Let the ..
Find what the minimum possible thickness of the oil film : A film of oil of index of refraction n = 1.44 floats on water (n = 1.33). Determine the minimum possible thickness of the oil film
Thermal anemometry is used to determine the mass flow rate : Thermal anemometry is used to determine the mass flow rate of water through a pipe. A wire dissipating heat is installed in the pipe. Upstream of the wire, the temperature is measured to be 20.3 C. Well downstream of the wire, where the fluid is suff..
What was the percent increase in the spring compression : You compress a spring by a certain distance. What was the percent increase in the spring's compression distance

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Complete a standard schematic diagram of the power cycle

a solar-thermal-electric power plant collects energy from sunlight focused on a high-temperature collector where solar

  Location of the solid-liquid interface at steady state

A t=10-mm-thick horizontal layer of water has a top surface temperature of Tc = - 4 C and a bottom surface temperature of Th = 2 C. Determine the location of the solid-liquid interface at steady state.

  Modeling the air as ideal gas with constant specific heats

Air is contained in a piston-cylinder assembly, initially at 40 lbf/in2 and 600 ?R. The air expands in a poly tropic process with n = k = 1.4 until the volume is doubled. Modeling the air as an ideal gas with constant specific heats,

  Eight kilograms of the gas are heated from 17 to 187 k at

an ideal gas has a constant-pressure specific heat of 2.20 kjkgk and a molar mass of 16.04. eight kilograms of the gas

  What pressure would the air on the left need to be pumped

a partitioned tank contains water and mercury. what is the gauge pressure in the air trapped in the left chamber? what

  Determine total and flow energies of the steam per unit mass

Steam is leaving a pressure cooker whose operating pressure is 30 psia. It is observed that the amount of liquid in the cooker has decreased by 0.45 gal in 60 minutes after the steady operating conditions are established, and the cross-sectional area..

  What are the mole fractions of the liquid phase

A vapor composed of 0.90 mole fraction ethanol and 0.10 mole fraction acetic acid at 120.0 mmHg (absolute), is in equilibrium with a liquid phase also composed of ethanol and acetic acid.

  The arm of the robot has a fixed length of r3ft and it

the arm of the robot has a fixed length of r3ft and it grips a moves along the path z3sinthetaft where theta is in

  A piece of steel has a conductivity of k 15 wmk and a

a piece of steel has a conductivity of k 15 wmk and a brick has k1wmk. how thick a steel wall will provide the same

  What is the type of analog anti aliasing filter

what is the type of analog anti aliasing filter in DSA HP3566a? is that butterworth, chebyshev, inverse chebyshev or elliptic? and what order of that filter? thanks very much.

  What will be the temperature of the steam after the

at 500 bar and 500 deg c undergoes a throttling expansion to 1 bar. what will be the temperature of the steam after the

  The hill has an elevation of 77 ft and an inclination of 4

a man is changing his tire at the top of a hill. he is rolling the spare at 4.83 fts when he loses control and the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd